Abstract:Ultra-high performance concrete (UHPC) has a high self-healing capacity and is prone to bursting after exposure to high temperatures due to its characteristics. This work evaluates the damage and improvement of UHPC with coarse aggregates through mechanical properties (compressive strength and ultrasonic pulse velocity), transport properties (water absorption and a chloride diffusion test), and micro-properties such as X-ray diffraction (XRD), Mercury intrusion porosimetry (MIP), and Scanning electronic microscopy (SEM). The result demonstrates that polypropylene (PP) fibers are more suitable for high temperature tests than polyacrylonitrile (PAN) fibers. The result shows that 400 °C is the critical temperature point. With the increase in temperature, the hydration becomes significant, and the internal material phase changes accordingly. Although the total pore volume increased, the percentage of various types of pores was optimized within 400 °C. The mass loss gradually increased and the ultrasonic pulse velocity gradually decreased. While the compressive strength first increased and then decreased, and the increase occurred within 25–400 °C. As for the transport properties, the chloride migration coefficient and capillary absorption coefficient both increased dramatically due to the higher sensitivity to temperature changes. The results of the property improvement test showed that at temperatures above 800 °C, the compressive strength recovered by more than 65% and the ultrasonic pulse velocity recovered by more than 75%. In terms of transport properties, compared to the results before self-healing, the chloride migration coefficient decreased by up to 59%, compared with 89% for the capillary absorption coefficient, after self-healing at 800 °C. With respect to the enhancement effect after exposure to high temperatures, the environment of a 5% Na2SO4 solution was not as good as the clean water environment. The corresponding changes in microstructure during the high temperatures and the self-healing process can explain the change in the pattern of macroscopic properties more precisely.

Effect of High Temperature on the Mechanical Properties of Hierarchical Porous Cenosphere/geopolymer Composite Foams

Crystallization Behavior and Mechanical Properties of High Open Porosity Dolomite Hollow Microspheres Filled Hybrid Geopolymer Foams

Microstructure evolution and properties of red mud/slag-based cenosphere/geopolymer foam exposed to high temperatures

Preparation of eco-friendly porous ceramic with low thermal conductivity by high-temperature treatment of foamed solid waste based geopolymer with cenospheres

Effect of fibers addition on mechanical properties of eco-friendly phosphogypsum-based composite at high temperatures

Enhanced Interfacial, Mechanical, and Anti-Hygrothermal Properties of Carbon Fiber/cyanate Ester Composites with the Catalytic Sizing Agents of Titanium Epoxy

Experimental Investigation of Heating–cooling Effects on the Mechanical Properties of Geopolymer-Based High Performance Concrete Heated to Elevated Temperatures

Correlation Between Macroscopic Properties and Microscopic Pore Structure in Steel-Basalt Hybrid Fibers Reinforced Cementitious Composites Subjected to Elevated Temperatures

Effect of high temperature heating on the microstructure and performance of cesium-based geopolymer reinforced by cordierite

Fabrication and characterization of foamed ceramics with a hierarchical pore structure from pyrite‐rich cyanide tailing

Study on Micro-mesoscale Characterization and Impact Load Mechanical Properties of Ultra-High-Performance Concrete After Sustained Elevated Temperature

Preparation and characterization of Cf/Pollucite composites through geopolymer precursors

Green Synthesis of High Porosity Waste Gangue Microsphere/geopolymer Composite Foams Via Hydrogen Peroxide Modification

Microstructure and Mechanical Properties of High-Toughness Fiber-Reinforced Cementitious Composites after Exposure to Elevated Temperatures

Effect of Curing Temperature on High-Strength Metakaolin-Based Geopolymer Composite (HMGC) with Quartz Powder and Steel Fibers

Pore structure and thermal oxidation curing behavior of porous polymer derived ceramics with superhigh porosity fabricated by freeze casting

High temperature and mesostructure effect on aluminum foam compression responses

Atomic-Scale Insights into the Effects of the Foaming Degree on the Glass–Ceramic Matrix Derived from Waste Glass and Incineration Bottom Ash

Mechanical Properties of HPC Incorporating Fly Ash and Ground Granulated Blast Furnace Slag After Exposure to High Temperatures

Study on the high-temperature resistance of metakaolin-fly ash-based geopolymers

Transport Properties and Resistance Improvement of Ultra-High Performance Concrete (UHPC) after Exposure to Elevated Temperatures