Abstract:The investigation on geopolymers has intrigued broad interests in the past decades, due to the requirements for the recycling of aluminosilicate solid wastes, such as red mud, slags, sludges and demolished concrete. Previous studies have demonstrated the feasibility of reusing this Aluminosilicate as a resource to prepare cementitious materials and indicated their promising properties at ambient temperature. However, when this material was exposed to high temperatures, especially above 1000 °C, the microstructure evolution mechanisms were not systematically investigated. In this study, the microstructural evolution process of metakaolin-based K geopolymer (molar ratio of K:Al:Si was 1:1:4) is investigated. The crystalized leucite originated from the geopolymer precursor was detected above 1000 °C. The SEM results indicate that the microstructure of the geopolymer before heating was composed of non-reacted metakaolin with a typical layered structure and reacted amorphous binder phase. As the geopolymer heated to 1000 °C, the microstructure of the geopolymer changed to a porous structure with an average pore size from 10 to 30 μm. When the heating temperature reached 1100 °C, the pores started to close along with the leucite crystallization process. As the heating temperature reached 1200 °C, most of the pores were closed. The TEM results show that the microstructure of the geopolymer, after being heated to 1400 °C, was composed of an amorphous glassy phase and crystallized leucite phase. The crystallized leucite grains originated from the nano-sized crystal nuclei, with an average size of 2–3 nm. The TEM-EDS results indicate that the chemical composition of the glassy phase was complicated. It varied from area to area because of the movement and uneven distribution of K.

Microstructure and Integrity of Leucite Ceramic Derived from Potassium-Based Geopolymer Precursor

Microstructure Evolution Mechanism of Geopolymers with Exposure to High-Temperature Environment

Preparation of fully stabilized cubic-leucite composite through heat-treating Cs-substituted K-geopolymer composite at high temperatures

Effect of high temperature heating on the microstructure and performance of cesium-based geopolymer reinforced by cordierite

Effect of cesium substitution on the thermal evolution and ceramics formation of potassium-based geopolymer

Thermal evolution and crystallization kinetics of potassium-based geopolymer

Interface evolution of the Cf/leucite composites derived from Cf/geopolymer composites

In situ processing of MWCNTs/leucite composites through geopolymer precursor

High Temperature Properties of Geopolymeric Ceramic

Synthesis of Leucite from Potash Feldspar

Effects of high-temperature heat treatment on the microstructure and mechanical performance of hybrid Cf-SiCf-(Al2O3p) reinforced geopolymer composites

Preparation,Crystallization and Mechanical Properties of Potassium Aluminosilicate Glass-ceramics

Thermal Evolution of Lithium Ion Substituted Cesium-Based Geopolymer under High Temperature Treatment, Part I: Effects of Holding Temperature

Phase transition and thermal stability of ceramics from Na‐based geopolymers

Celsian Formation from Barium-Exchanged Geopolymer Precursor: Thermal Evolution

Monoclinic-celsian Ceramics Formation: Through Thermal Treatment of Ion-Exchanged 3D Printing Geopolymer Precursor

Formation of SiC whiskers/leucite-based ceramic composites from low temperature hardening geopolymer

Low-temperature sintered pollucite ceramic from geopolymer precursor using synthetic metakaolin

Microstructure and Mechanical Properties of Ceramics Obtained from Chemically Co-Precipitated Al 2 O 3 -Gdalo 3 Nano-Powders with Eutectic Composition

From Bulk to Porous Structures: Tailoring Monoclinic SrAl2Si2O8 Ceramic by Geopolymer Precursor Technique

Optimization of hydrothermal autoclaving parameters for the synthesis of porous ceramics from porcelain tile polishing residue