Abstract:High efficiency, large capacity, and low energy consumption have become an important challenge in performances of post-combustion carbon dioxide (CO2) capture and regeneration. Blended absorbents have shown great potential but their process simulation, modeling, and optimization have not been known definitively. This work developed the blended aqueous absorbents based on piperazine (PZ) activators: PZ-activated methyldiethanolamine (MDEA), potassium carbonate solution (K2CO3), and aqueous ammonia (NH3H2O) to improve their techno-economic performances. The whole process simulation was conducted using a validated rate-based model under given a CO2 capture efficiency of 85%. In this process, the key factors including the molar concentration of the absorbent, PZ molar ratio, CO2 load of lean liquid, lean-liquid temperature, flue-gas temperature, and rich-liquid temperature, were employed for the design of experiment using response surface methodology. A series of nonlinear regression equations were developed using the flow rate of absorbents, the reboiler heat duty (in the units of gigajoules per ton of CO2), and the cooling-water flow rate as the multi-objective function. Subsequently, the optimal Pareto solution set and compromise solutions were determined using the multi-objective genetic algorithm and finally, their performances were assessed using the fuzzy close-degree algorithm. It was found that the optimal operating parameters can be determined effectively according to the proposed approach. For each PZ-activated blended absorbents, the trade-off effect exists between absorbent flow rate, reboiler heat duty, and cooling water consumption. The absorbents having optimal techno-economic performance were recommended to be PZ-activated MDEA, followed by PZ-activated K2CO3 and PZ-activated NH3H2O when considering the regeneration energy consumption. The results may provide a positive reference for process design and optimization of the industrial post-combustion CO2 capture system.

Process Design and Optimization of State‐of‐the‐art Carbon Capture Technologies

Systematic Design and Optimization of a Membrane–Cryogenic Hybrid System for CO2 Capture

Collaborative Optimization for a Multi-Energy System Considering Carbon Capture System and Power to Gas Technology

Analysis and optimization of post-combustion CO2capture system based on chemical absorption

Energy-efficient Process Intensification for Post-Combustion CO2 Capture: A Modeling Approach

Multistage Circulation Absorption Improvement: Simulation and Energy-Saving Evaluation of an Innovative Amine-Based CO2 Capture Process

Comprehensive 3E Analysis and Multi-Objective Optimization of a Novel Process for CO2 Capture and Separation Process from Syngas

Comparative study on process simulation and performance analysis in two pressurized oxy-fuel combustion power plants for carbon capture

CO2 Capture Analysis in Different Combustion Methods for CO2 Utilisation and Storage

Process simulation, optimization and assessment of post-combustion carbon dioxide capture with piperazine-activated blended absorbents

Process Simulation and Energy Consumption for CO<SUB Align="right">2 Capture with Different Flowsheets

Optimization of Carbon Capture Process Using Aqueous Ammonia with Rate-Based Simulation Method

Optimization of Parameters and Thermodynamics of Gasification Process for Enhanced CO2 Capture in an IGCC System

Study on process intensification of pre combustion CO capture

Simulation Optimization of A New Ammonia-Based Carbon Capture Process Coupled with Low-Temperature Waste Heat Utilization

Modelling and Process Analysis of Post-Combustion Carbon Capture with the Blend of 2-Amino-2-methyl-1-propanol and Piperazine

Design and performance evaluation of a novel system integrating Water-based carbon capture with adiabatic compressed air energy storage

Dynamic modelling and simulation of a post-combustion CO2 capture process for coal-fired power plants

Optimization of Post Combustion CO2 Capture from a Combined-Cycle Gas Turbine Power Plant via Taguchi Design of Experiment

Progress in Post-Combustion Technology for Carbon Dioxide Capture

A Novel Coal-Based Calcium Carbide-Acetylene System Process Based on Multistage Carbon Capture and Waste Slag Recycling Design: A Multiobjective Optimization Evaluation Perspective