Abstract:In this study, the process of carbon dioxide (CO2) capture directly from ambient air in a conventional monoethanolamine (MEA) absorption process was simulated and optimized using a rate-based model in Aspen Plus. The process aimed to capture a specific amount (148.25 Nm3/h) of CO2 from the air, which was determined by a potential application aiming to produce synthetic methane from the output of a 2.7 MW electrolyser (593 Nm3/h H2). We investigated the technical performance of the process by conducting a sensitivity analysis around different parameters such as air humidity, capture rate defined as a ratio of moles of CO2 captured during the process to the total mole of CO2 in the feed stream, CO2 loading of lean and rich absorption liquids and reboiler temperature, and evaluated the energy consumption and overall cost in this system. In order to meet the design requirement for standard packed columns, the rich absorption liquid was circulated to the top of the absorber. A capture rate of 50% was selected in this process as a baseline. At higher capture rates, the required energy per ton of captured CO2 increases due to a higher steam stripping rate, required in the desorber, and at lower capture rates, the size of equipment, in particular, absorber and blowers increases due to the need for processing a significantly larger volume of air at the given CO2 production volume. At the base case scenario, a reboiler duty of 10.7 GJ/tCO2 and an electrical energy requirement of 1.4 MWh/tCO2 were obtained. The absorber diameter and height obtained were 10.4 and 4.4 m, respectively. The desorber is found to be relatively small at 0.54 m in diameter and 3.0 m in height. A wash water section installed at top of the absorber decreased the MEA loss to 0.28 kg/ton CO2. However, this increased capital cost by around 60% resulting in CO2 capture costs of $1,691 per ton CO2 for the MEA base scenario. Based on the techno-economic analysis, assuming a non-volatile absorbent rather than MEA thereby avoiding a wash water section, and using an absorption column built from cheaper materials, the estimated cost per ton of CO2 produced was reduced to $676/tCO2. The overall cost range was between $273 and $1,227 per ton of CO2 depending on different economic parameters such as electricity ($20–$200/MWh) and heat price ($2–$20/GJ), plant life (15–25 years) and capital expenditure (±30%). In order to reduce the cost further, the use of innovative cheap gas-liquid contactors that operate at lower liquid to gas ratios is crucial.

Optimization of Post Combustion CO2 Capture from a Combined-Cycle Gas Turbine Power Plant via Taguchi Design of Experiment

Systematic Design and Optimization of a Membrane–Cryogenic Hybrid System for CO2 Capture

Post-combustion CO2 capture from a natural gas combined cycle power plant using activated carbon adsorption

Optimal Design of a Subambient Membrane Separation System with Work and Heat Integration for CO2 Capture

Influence of Gas Turbine Exhaust CO2 Concentration on the Performance of Post Combustion Carbon Capture Plant

Techno-Economic Assessment for CO2 Capture From Air Using a Conventional Liquid-Based Absorption Process

Energy-efficient Process Intensification for Post-Combustion CO2 Capture: A Modeling Approach

Optimizing post-combustion carbon capture: A comprehensive 3E analyses of energy, exergy, and exergoeconomic aspects with solar integration

Carbon Capture and Storage Energy Consumption and Performance Optimization Using Metamodels and Response Surface Methodology

New improvement of amine-based CO2 capture processes using heat integration and optimization

Optimization of Carbon Capture Process Using Aqueous Ammonia with Rate-Based Simulation Method

Optimizing the CO 2 capture and removal process to recover energy and CO 2 from the flue gas of boilers and gas turbines outlet with considering the techno-economic analysis

Systematic study of aqueous monoethanolamine‐based CO2 capture process: model development and process improvement

Simulation Optimization of A New Ammonia-Based Carbon Capture Process Coupled with Low-Temperature Waste Heat Utilization

Modeling and Simulation of CO2 Capture Unit using Mixed Solvent of Aqueous Methyldiethanolamine and Piperazine for 6.4 MWe Power Plant

Modelling and Process Analysis of Post-Combustion Carbon Capture with the Blend of 2-Amino-2-methyl-1-propanol and Piperazine

Sensitivity Analysis of Post Combustion Carbon Capture Using Monoethanolamine (MEA) as a Solvent. A Simulation Study

A multiobjective experimental based optimization to the CO2 capture process using hybrid solvents of MEA-MeOH and MEA-water

Post-combustion carbon capture process modeling, simulation, and assessment of synergistic effect of solvents

The parameters optimization for a CFBC pilot plant experimental study of post-combustion CO2 capture by reactive absorption with MEA

Dynamic Operation and Simulation of Post-Combustion CO2 Capture