Abstract:In this study, the process of carbon dioxide (CO2) capture directly from ambient air in a conventional monoethanolamine (MEA) absorption process was simulated and optimized using a rate-based model in Aspen Plus. The process aimed to capture a specific amount (148.25 Nm3/h) of CO2 from the air, which was determined by a potential application aiming to produce synthetic methane from the output of a 2.7 MW electrolyser (593 Nm3/h H2). We investigated the technical performance of the process by conducting a sensitivity analysis around different parameters such as air humidity, capture rate defined as a ratio of moles of CO2 captured during the process to the total mole of CO2 in the feed stream, CO2 loading of lean and rich absorption liquids and reboiler temperature, and evaluated the energy consumption and overall cost in this system. In order to meet the design requirement for standard packed columns, the rich absorption liquid was circulated to the top of the absorber. A capture rate of 50% was selected in this process as a baseline. At higher capture rates, the required energy per ton of captured CO2 increases due to a higher steam stripping rate, required in the desorber, and at lower capture rates, the size of equipment, in particular, absorber and blowers increases due to the need for processing a significantly larger volume of air at the given CO2 production volume. At the base case scenario, a reboiler duty of 10.7 GJ/tCO2 and an electrical energy requirement of 1.4 MWh/tCO2 were obtained. The absorber diameter and height obtained were 10.4 and 4.4 m, respectively. The desorber is found to be relatively small at 0.54 m in diameter and 3.0 m in height. A wash water section installed at top of the absorber decreased the MEA loss to 0.28 kg/ton CO2. However, this increased capital cost by around 60% resulting in CO2 capture costs of $1,691 per ton CO2 for the MEA base scenario. Based on the techno-economic analysis, assuming a non-volatile absorbent rather than MEA thereby avoiding a wash water section, and using an absorption column built from cheaper materials, the estimated cost per ton of CO2 produced was reduced to $676/tCO2. The overall cost range was between $273 and $1,227 per ton of CO2 depending on different economic parameters such as electricity ($20–$200/MWh) and heat price ($2–$20/GJ), plant life (15–25 years) and capital expenditure (±30%). In order to reduce the cost further, the use of innovative cheap gas-liquid contactors that operate at lower liquid to gas ratios is crucial.

Carbon Capture and Storage Energy Consumption and Performance Optimization Using Metamodels and Response Surface Methodology

Systematic Design and Optimization of a Membrane–Cryogenic Hybrid System for CO2 Capture

A multiobjective experimental based optimization to the CO2 capture process using hybrid solvents of MEA-MeOH and MEA-water

Optimization of Post Combustion CO2 Capture from a Combined-Cycle Gas Turbine Power Plant via Taguchi Design of Experiment

New improvement of amine-based CO2 capture processes using heat integration and optimization

Sensitivity Analysis of Post Combustion Carbon Capture Using Monoethanolamine (MEA) as a Solvent. A Simulation Study

Mathematical Modelling and Experimental Investigation of CO2 Absorber Recovery Using an Electro-Acidification Method

Modelling and Process Analysis of Post-Combustion Carbon Capture with the Blend of 2-Amino-2-methyl-1-propanol and Piperazine

Experimental And Rate-Based Modeling Study Of Co2 Capture By Aqueous Monoethanolamine

Multi-stage Solvent Circulation Absorption Enhancement: System Optimization for Energy-Saving CO2 Capture

Systematic study of aqueous monoethanolamine‐based CO2 capture process: model development and process improvement

Optimizing post-combustion carbon capture: A comprehensive 3E analyses of energy, exergy, and exergoeconomic aspects with solar integration

Rate-Based Modelling and Validation of an Absorber and Stripper in an Amine-Based Post-Combustion CO2 Capture Process

Energy optimization of a non-aqueous solvent CO 2 absorption system with pressure swing regeneration

Energy-efficient Process Intensification for Post-Combustion CO2 Capture: A Modeling Approach

Process Simulation and Energy Consumption for CO<SUB Align="right">2 Capture with Different Flowsheets

Techno-Economic Assessment for CO2 Capture From Air Using a Conventional Liquid-Based Absorption Process

Post-combustion carbon capture process modeling, simulation, and assessment of synergistic effect of solvents

Using Machine Learning for Comparative Optimizing a Novel Integration of Molten Carbonate and Solid Oxide Fuel Cells with CO2 Recovering and Gasification

Utilizing the Thermal Energy from Natural Gas Engines and the Cold Energy of Liquid Natural Gas to Satisfy the Heat, Power, and Cooling Demands of Carbon Capture and Storage in Maritime Decarbonization: Engineering, Enhancement, and 4E Analysis

Multistage Circulation Absorption Improvement: Simulation and Energy-Saving Evaluation of an Innovative Amine-Based CO2 Capture Process