Abstract:The adsorption and desorption process of selenium (Se) clusters, especially small molecule Se3 and Se4, on graphite enhance the diffusion and reaction activity of traditional Se particles, thereby improving the chemical environment for grain growth, optimizing the film crystallinity, and passivating defects, and finally making the device efficiency up to 14.5% with a VOC of 553.1 mV. Insufficient selenization and uneven distribution of elements caused by the poor diffusion and reaction activity of selenium clusters is one of the main issues limiting the efficiency of Cu2ZnSn(S,Se)4 (CZTSSe) solar cells. Here, this work designs a simple and feasible strategy to improve the activity of selenium (Se) by implementing high‐temperature treatment on graphite boxes loaded with Se pellets. The rapid adsorption/desorption characteristics of graphite on active gaseous small‐molecule selenium have successfully introduced hyperactive Se4, Se3, and Se2 into the selenization process. The results indicate that the adsorbed non‐toxic gaseous active Se3 and Se4 can quickly and uniformly diffuse into the precursor film at low temperatures, thereby inducing nucleation and grain growth at both surface and back interface simultaneously, which inhibits the upward migration and aggregation of cations, especially Cu, and promotes the homogenization of elements. The overall relatively Cu‐poor chemical environment suppresses the formation of CuZn defects and [2CuZn+SnZn] defect clusters, and also promotes the generation of favorable VCu. The band tail states and non‐radiative recombination are then optimized. Finally, the CZTSSe solar cells achieve a power conversion efficiency (PCE) of 14.5%, with VOC/VOCSQ of 67% being one of the highest in the literature.

The Influence of Cracked Selenium Flux on CIGS Thin Film Growth and Device Performance Prepared by Two-Step Selenization Processes

Increasing surface band gap of Cu(In,Ga)Se2 thin films by post depositing an In-Ga-Se thin layer.

Effect of Se Vapor Concentration on Cigs Film Preparation

Impact of selenization with NaCl treatment on the physical properties and solar cell performance of crack-free Cu(In,Ga)Se2 microcrystal absorbers

Pulse Selenization in Cu(In,Ga)Se 2 Solar Cells: A Promising Approach to Achieve High Efficiency by Electrodeposition

Study on Two-Step Process of Preparing CIGS Films

Investigation of Cu(In,Ga)Se2 Polycrystalline Growth: Ga Diffusion and Surface Morphology Evolution

Preparation And Characterization Of Cu(In,Ga)Se-2 Thin Films By Selenization Of Cu0.8ga0.2 And In2se3 Precursor Films

Eliminating the Excess CuxSe Phase in Cu-rich Cu(In,Ga)Se2 by In2Se3 Treatment

Influence of Silicon Oxide Processes on the Performance of Copper Indium Gallium Selenide Flexible Solar Cells

Growth and Characterization of Copper Indium Gallium Diselenide Films for Solar Cells Fabrication

Passivation of Deep‐Level Defects through Chemical Environment Regulation for Efficient CZTSSe Solar Cells Based on Active Selenium Adsorption–Desorption Process

Influence of a Precursor Film with a Copper Gradient on the Properties of a Copper Indium Gallium Selenide Solar Cell

Fabricating Cu(In,Ga)Se2 (CIGS) Thin Films with Large Grains Based on the Quaternary CIGS Targets

The Influence of Selenization Temperature on the Properties of CuInGaSe2 Thin Film

Unravelling the Intricacies of Selenization in Sequentially Evaporated Cu(In,Ga)Se2 Thin Film Solar Cells on Flexible Substrates

Investigation of Copper Indium Gallium Selenide Material Growth by Selenization of Metallic Precursors

Passivation of Deep-Level Defects by Cesium Fluoride Post-Deposition Treatment for Improved Device Performance of Cu(In,Ga)Se2 Solar Cells.

Effect of Cd diffusion on the electrical properties of the Cu(In,Ga)Se2 thin-film solar cell

Influences Of The Selenization Duration On Compositions And Microstructures Of Cigs Absorber

The Effects of Selenium Content on Cu(Inga)Se-2 Thin Film Solar Cells by Sputtering from Quaternary Target with Se-Free Post Annealing