Abstract:Fabricating chalcopyrite Cu(In,Ga)Se2 (CIGS) films from electrodeposition is one of the most effective ways to lower the production cost and energy consumption compared with that from vacuum methods. However, this process often produces a pronounced rough surface with impurity phases, induces the accumulation of gallium, and results in a low surface band gap. In this work, ammonium sulfide ((NH4)2S, AS) solution treatment is used as a single way to realize the optimization of the distribution of elements on the CIGS surface. It is revealed that this room-temperature process not only significantly reduces the surface roughness (Ra) but also incorporates sulfur (S) into the CIGS film successfully. An appropriate AS treatment duration can effectively remove the impurity phases and reduce the series resistance, and thus the dominant recombination moves from the CdS/CIGS heterojunction interface to the bulk. Consequently, the open-circuit voltage (VOC) and fill factor (FF) of solar cells have been greatly improved (from 484 to 532 mV, from 62.52 to 68.15%), leading to higher efficiency of 11.92%. This work focuses on revealing the etching mechanism of the CIGS films by the AS treatment at room temperature.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.1c00220?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.1c00220</a>.Best solar cell parameters of different unannealing samples (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.1c00220/suppl_file/ae1c00220_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Influence of Silicon Oxide Processes on the Performance of Copper Indium Gallium Selenide Flexible Solar Cells

Metal Precursor with Bi-Layer Indium for Cu(In,Ga)Se2 Thin Film Preparation

Effects of Alkali Elements on Copper Indium Gallium Aluminum Selenide Flexible Solar Cells Fabricated on Polyimide Substrates

Optimization of CuInGaSSe properties and CuInGaSSe/CdS interface quality for efficient solar cells processed with CuInGa precursors

Efficiency enhancement of copper indium gallium selenide solar cells fabricated on polyimide foils with multiple metal layers

Influence of a Precursor Film with a Copper Gradient on the Properties of a Copper Indium Gallium Selenide Solar Cell

Influences of Ga Concentration on Performances of CuInGaSe2 Cells Fabricated by Sputtering-Based Method with Ceramic Quaternary Target

Enhancing Surface Properties for Electrodeposited Cu(In,Ga)Se 2 Films by (NH 4 ) 2 S Solution at Room Temperature

Influences of Sulfurization on Performances of Cu(In,Ga)(Se,S)2 Cells Fabricated Based on the Method of Sputtering CIGSe Quaternary Target

Unravelling the Intricacies of Selenization in Sequentially Evaporated Cu(In,Ga)Se2 Thin Film Solar Cells on Flexible Substrates

Numerical Simulation of Copper Indium Gallium Diselenide Solar Cell with Ultra-Thin BaSi2 Back Surface Field Layer Using the Non-Toxic In2Se3 Buffer Layer

Efficiency improvement of electrodeposition-processed Cu(In,Ga)Se2 solar cell with widen surface bandgap by spin-coating In2S3 thin film

Surface modifications of CIGS absorbers and their effects on performances of CIGS solar cells

Cu(In,Ga)Se-2 Solar Cells Fabricated by Sputtering from Copper-Poor and Selenium-Rich Ceramic Target with Selenium-Free Post Treatment

Growth and Characterization of Copper Indium Gallium Diselenide Films for Solar Cells Fabrication

Study on Two-Step Process of Preparing CIGS Films

Mechanism‐Based Approach of CdS/Cu(In,Ga)Se2 (CIGS) Interfaces for CIGS Solar Cells Through Deposition in Different Stages of Continuous Chemical Bath Deposition Reaction: Key to Achieving High Photovoltaic Performance

10.3%-Efficient Submicron-Thick Cu(In,Ga)Se2 Solar Cells with Absorber Fabricated by Sputtering In2Se3, CuGaSe2 and Cu2Se Targets

Optoelectronic Effects of Copper–Indium–Gallium–Sulfur (CIGS2)-Solar Cells Prepared by Three-Stage Co-Evaporation Process Technology

Preparation of Cu(In,Ga)Se2 Thin Film by Sputtering from Cu(In,Ga)Se2 Quaternary Target

Inhibiting Aluminum Oxidation in CuInAl Precursor Films: Significance for Achieving High-Performance Cu(InAl)Se2 Solar Cells