Abstract:Oxide dispersion strengthened tungsten (ODS-W) is a potential candidate for plasma-facing materials (PFMs) in future fusion reactors. In this work, deuterium (D) retention and surface blistering in W-1 wt% La2O3 (W-La2O3) have been investigated after exposure to low-energy (40 eV) D plasma with various exposure temperatures (400–600 K) and fluences (3.6 × 1024–1.4 × 1025 D/m2). Surface blistering and D retention exhibit a strong dependence on the exposure temperature and fluence. The most pronounced effect is found at 500 K. The blister-induced defects including dislocations and vacancies are considered to dominate the D retention. At 400 K and 600 K, the D retained in W-La2O3 is governed by unique intrinsic defects including interfaces, micro-pores, and unoxidized La particles. Regarding the exposure fluence, as expected, surface blistering and D retention are positively correlated with it, in which two dominant stages of nucleation and growth for blistering are identified from the changes in area density and size of blisters. Based on the results obtained from W-La2O3, comparisons with W are performed with the exposure condition (500 K, 1.4 × 1025 D/m2) where the blistering and D retention is most pronounced. Although the area density of blisters is similar between the two materials, the average size of blisters is larger in W-La2O3. Notably, an additional high-temperature D desorption shoulder appears in the release spectra of W-La2O3, which is probably due to the particular defects such as interfaces, micro-pores and La particles, and finally resulting in a higher D retention in W-La2O3 than that in W.

Suppression of Cavitation in Melted Tungsten by Doping with Lanthanum Oxide

Tungsten Joining with Copper Alloy and Its High Heat Load Performance

Influence of Surface Morphology and Microstructure on Performance of CVD Tungsten Coating under Fusion Transient Thermal Loads

Melt layer erosion of pure and lanthanum doped tungsten under VDE-like high heat flux loads

Experimental and Numerical Simulations of ELM-like Transient Damage Behaviors to Different Grade Tungsten and Tungsten Alloys

Influence of Surface Melting on the Deuterium Retention in Pure and Lanthanum Oxide Doped Tungsten

Surface Modification of W–V Alloy Exposed to High Heat Flux Helium Neutral Beams

Effects of Tantalum Alloying on Surface Morphology and Deuterium Retention in Tungsten Exposed to Deuterium Plasma

Blistering Behavior and Deuterium Retention in Tungsten Vanadium Alloys Exposed to Deuterium Plasma in the Linear Plasma Device STEP

Balling Phenomena in Selective Laser Melted Tungsten

Melting and Solidifying Behavior in Single Layer Selective Laser of Pure Tungsten Powder

Dependence of deuterium retention and surface blistering on deuterium plasma exposure temperature and fluence in lanthanum oxide doped tungsten

Investigation on the ablation behavior of cemented tungsten carbide by a nanosecond UV laser

Microstructural Effects of Y2O3 and TiC Additions in Tungsten

Microstructure and performance of rare earth element-strengthened plasma-facing tungsten material

Microstructure Evolution and Effect on Deuterium Retention in Oxide Dispersion Strengthened Tungsten During He+ Irradiation

Lanthanum Hydride Doped Tungsten-Based Coating Fabricated by Supersonic Atmospheric Plasma Spraying

Selective laser melting of lanthanum oxide-reinforced tungsten composites: microstructure and mechanical properties

Experimental and Numerical Studies of Tungsten Line Growth in Laser Chemical Vapor Deposition

Surface Blistering and D Desorption in High-Energy-rate Forging W, W-Y2O3, W-TiC Exposed to Deuterium Plasma

Microstructure and High-Temperature Ablation Behaviour of Hafnium-Doped Tungsten-Yttrium Alloys