Abstract:W-Ni alloy has been an important engineering material in military, nuclear industry and many other fields because of its excellent properties such as high strength and superior heat/corrosion/oxidation resistances. As a mainstream additive manufacturing technology based on powder-bed-fusion principle, selective laser melting (SLM) is suitable for the rapid fabrication of very complex W-Ni alloy components. However, researches on the powder densification behavior and microstructure formation mechanism of SLM W-Ni alloy are not thorough enough. In this work, a series of W-xNi (x = 16, 23, 30 wt.%) binary alloy samples were fabricated by SLM, using W/Ni mixed powders as the raw materials. The densification behaviors of the W/Ni mixed powders and the microstructure formation mechanisms of the different SLM W-Ni samples were studied. The results showed that when the W/Ni mixed powder bed was scanned by the laser, Ni powders with a relatively lower melting point would melt completely whereas W powders with a relatively higher melting point would rearrange themselves in the liquid Ni and only part of them could be dissolved into the liquid Ni. As the initial content of Ni powders increased, the rearrangement and dissolution of W powders proceed more sufficiently, thus leading to the improvement in densification degree. The relative densities of the W-16Ni, W-23Ni and W-30Ni SLM samples are 92.87 ± 0.67%, 98.66 ± 0.26% and 99.67 ± 0.18%, respectively. During the solidification processes of W-Ni molten pools, the precipitation of W grains from liquid Ni, the transformation of liquid Ni to γ-Ni solid solution and the precipitation of Ni2W from γ-Ni solid solution would occur in sequence. For the W-16Ni and W-23Ni samples, the grain morphology of the W precipitations is dendritic. For the W-30Ni samples, the W precipitations are globular. As a result of the unique melting- solidification behaviors, all the SLM samples possessed a tri-modal microstructure composed of unmelted W particles, dendritic/globular W grains, and γ-Ni solid solution with Ni2W intragranular precipitation. The average microhardness of the SLM W-Ni alloy samples decreased with the increase of Ni content, which could be explained by the variation in defect and microstructure features.

Densification, microstructural evolutions of 90W-7Ni-3Fe tungsten heavy alloys during laser melting deposition process

Laser melting deposition of fine-grained 90 W-7Ni-3Fe alloys using pre-sintered granulated powder

Microstructure Evolution and Mechanical Properties of Tungsten Alloy Prepared by Laser Directed Energy Deposition

Revealing the Solidification Microstructure Evolution and Strengthening Mechanisms of Additive-Manufactured W-FeCrCoNi Alloy: Experiment and Simulation

Microstructure and fracture behavior of 90W-7Ni-3Fe alloy fabricated by laser directed energy deposition

Densification, Microstructure And Properties Of 90w-7ni-3fe Fabricated By Selective Laser Melting

Selective Laser Melting of W-Ni-Cu Composite Powder: Densification, Microstructure Evolution and Nano-Crystalline Formation

Microstructure and Mechanical Properties of Additive Manufactured W-Ni-Fe-Co Composite Produced by Selective Laser Melting

Effects of laser printing parameters on molten pool formation, microstructure evolution and mechanical properties of laser directed energy deposition of difficult-to-process tungsten heavy-alloy

Ultrashort-time Liquid Phase Sintering of High-Performance Fine-Grain Tungsten Heavy Alloys by Laser Additive Manufacturing

Two optimized post-heat treatments to achieve high-performance 90W–7Ni–3Fe alloys fabricated by laser-directed energy deposition

Thermal behavior and microstructure evolution mechanism of W-20%Fe alloy fabricated by laser metal deposition

Solidification Morphology Analysis Of Tungsten Alloy By Laser Solid Forming With Multi-Channel Powder Feeding

Alloying Effects on the Microstructure and Properties of Laser Additively Manufactured Tungsten Materials

High-density Tungsten Fabricated by Selective Laser Melting: Densification, Microstructure, Mechanical and Thermal Performance

Dual-laser powder bed fusion of difficult-to-process tungsten heavy-alloy: Inhibition of inferior defects and integrated fabrication of thin-walled overhanging structures

Additive manufacturing of W–Fe composites using laser metal deposition: Microstructure, phase transformation, and mechanical properties

Powder densification behavior and microstructure formation mechanism of W-Ni alloy processed by selective laser melting

A Strategy to Achieve High-Strength WNiFe Composite-Like Alloys with Low W Content by Laser Melting Deposition

Selective laser melting fabricated tungsten with thin-walled structure: role of linear energy density on temperature evolution and manufacturing quality

Investigation of the Microstructure of Ti6Al4V Alloy by Coaxial Double Laser Metal-Wire Deposition