Abstract:Additive manufacturing (AM) is a highly promising technique for producing near-net-shape high-value aerospace components with intricate geometries. However, due to the susceptibility to hot cracking, high-volume-fraction Ni 3 (Al,Ti)-type precipitation-strengthened Ni-base superalloys typically used for these applications are usually difficult or even infeasible to manufacture via AM. Previous metallurgical methods to mitigate hot-cracking in AM usually compromise strength, resulting in a trade-off between hot-cracking resistance and strength. Here, we overcome this trade-off in AM of a multicomponent Ni-rich precipitation-strengthened high-entropy alloy (MNiHEA) Ni 46.23 Co 23 Cr 10 Fe 5 Al 8.5 Ti 4 W 2 Mo 1 C 0.15 B 0.1 Zr 0.02 (at%): synergizing remarkable hot-cracking resistance and ultrahigh strength. Crack-free MNiHEA is successfully fabricated via laser powder bed fusion (LPBF) without preheating, despite its high (Al+Ti) content of ∼7.4 wt%. This remarkable resistance to hot cracking arises from the comparatively low critical solidification range, the small average solidification cracking index, the suppression of the intermetallic phases in solidification, and the moderate hardening rate induced by the nanoprecipitates in aging, which are intrinsically imparted by thermodynamic and mechanical characteristics. The yield strength of the as-built-to-aged MNiHEA reaches ∼1.2 gigapascal, together with acceptable ductility. This ultrahigh strength outperforms its cast-to-aged counterpart by more than one-third and existing commercial superalloys CM247 and IN738LC. Such pronounced enhancement in strength is attained through multiple strengthening mechanisms, including solid-solution hardening, dislocation hardening, precipitation-hardening and grain-boundary strengthening. Our results demonstrate that intrinsic hot-cracking resistance can be utilized as a new metallurgical concept for mitigating hot-cracking without compromising strength in AM of high-temperature materials such as HEAs and superalloys.

Two optimized post-heat treatments to achieve high-performance 90W–7Ni–3Fe alloys fabricated by laser-directed energy deposition

High-temperature Oxidation Behavior of AlCoCrCuFeNi High-Entropy Alloy by Selective Laser Melting

Microstructure and fracture behavior of 90W-7Ni-3Fe alloy fabricated by laser directed energy deposition

Effects of laser printing parameters on molten pool formation, microstructure evolution and mechanical properties of laser directed energy deposition of difficult-to-process tungsten heavy-alloy

Densification, microstructural evolutions of 90W-7Ni-3Fe tungsten heavy alloys during laser melting deposition process

Tailoring properties of directed energy deposited Al-Mg alloy by balancing laser shock peening and heat treatment

Laser melting deposition of fine-grained 90 W-7Ni-3Fe alloys using pre-sintered granulated powder

The simultaneous improvement of strength and ductility of the 93W-4.6Ni-2.4Fe prepared by additive manufacturing via optimizing sintering post-treatment

Superior strength of laser-arc hybrid additive manufactured Al-Zn-Mg-Cu alloy enabled by a tunable microstructure

Effect of T6 heat treatment on microstructure and mechanical properties of Al–18Si–10Cu–10Ni–5Mn–5Mg alloy prepared by laser-directed energy deposition

Laser powder bed fusion of a tungsten-nickel-ferrum alloy via in-situ alloying: Densification, microstructure, and mechanical properties

Laser powder bed fusion of a novel nano-modified tungsten alloy with refined microstructure and enhanced strength

Alloying Effects on the Microstructure and Properties of Laser Additively Manufactured Tungsten Materials

Directed energy deposition of Al-Mg-Si alloys with fully-equiaxed microstructure and isotropic high strength/ductility

Influence of Tungsten Addition on Microstructure and Tensile Properties of Ti6Al4V Fabricated by Laser-Directed Energy Deposition

Superior strength-ductility in laser aided additive manufactured high-strength steel by combination of intrinsic tempering and heat treatment

A precipitation strengthened high entropy alloy with high (Al+Ti) content for laser powder bed fusion: Synergizing in trinsic hot cracking resistance and ultrahigh strength

Fabrication and Characterization of Tungsten Heavy Alloys with High W Content by Powder Metallurgy

Tailoring the microstructure and mechanical property of laser powder bed fusion fabricated Ti–6Al–2Sn–4Zr–2Mo via heat treatment

Achieving high-performance pure tungsten by additive manufacturing: Processing, microstructural evolution and mechanical properties

Significant transitions of microstructure and mechanical properties in laser additive manufacturing AlCoCrFeNi 2.1 eutectic high-entropy alloy under heat treatment