Abstract:After the converter steelmaking process, a considerable number of ferroalloys are needed to remove dissolved oxygen from the molten steel, but it also forms a lot of oxide inclusions that cannot be completely removed. At the same time, it increases the carbon emissions in the steel production process. After years of research, our team have developed a series of clean deoxidation technologies, including carbon deoxidation, hydrogen deoxidation, and waste plastic deoxidation of molten steel to address the aforementioned issues. In this study, thermodynamic calculations and laboratory experiments were employed to verify that carbon and hydrogen can reduce the total oxygen content in the molten steel melt to below 5 × 10 −6 and 10 × 10 −6 , respectively. An analysis of the deoxidation mechanisms and effects of polyethylene and polypropylene was also conducted. In addition, the applications of carbon deoxidation technology in different steels with the hot-state experiment and industrial production were discussed carefully. The carbon deoxidation experimental results of different steels were as follows: (1) the oxygen content of bearing steel was effectively controlled at 6.3 × 10 −6 and the inclusion number density was lowered by 74.73% compared to aluminum deoxidized bearing steel; (2) the oxygen content in gear steel was reduced to 7.7 × 10 −6 and a 54.49% reduction of inclusion number density was achieved with almost no inclusions larger than 5 μm from the average level of industry gear steels; (3) a total oxygen content of M2 high-speed steel was as low as 3.7 × 10 −6 . In industrial production practice, carbon deoxidation technique was applied in the final deoxidation stage for non-aluminum deoxidized bearing steel, and it yielded excellent results that the oxygen content was reduced to below 8 × 10 −6 and the oxide inclusions in the steel mainly consist of silicates, along with small amounts of spinel and calcium aluminate.

Optimization On Refining Slag And Tapping Deoxidation System For Carbon Structure Steel Without Calcium Treatment

Control of oxide inclusion for low carbon and low silicon steel

Optimizing RH refining process to maximize cleanliness of low-carbon low-silicon Al killed steel

New steelmaking process based on clean deoxidation technology

Development and prospects of molten steel deoxidation in steelmaking process

Optimum Composition of Cao-Sio2-Al2o3-Mgo Slag for Spring Steel Deoxidized by Si and Mn in Production

Optimizing Slag Content to Control Ds-Type Inclusions in 10B21 Cold Heading Steel

Effect of CaO/Al2O3 Ratio in Fluorine‐Free Refining Slag with Low Basicity on the Cleanliness of SWRS82B Steel

Deoxidation of Molten Steel with CaO-Al_2O_3 Based Refining Slag

Optimization of Mold Slag for Continuous Casting of Peritectic Steel

Optimization of Slag Chemistry Toward Inclusion Control for 28CrMo47 Drill Pipe Steel Based on Viscosity and Equilibration Studies

Control of Steel Composition and Evolution of Inclusions During Electroslag Remelting of NiCrMoV High‐Strength Steel

Study on oxygen blowing optimisation of reducing (FeO) content in slag in EAF steelmaking process with high ratio of hot metal to scrap

Cleanliness of molten steel in continuous casting tundish

Industrial Experiment of Technique Optimization on IF Steel in RH Degasser

Microstructure Refinement of Structural Steel in China

Study on properties of CaF 2 –CaO–Al 2 O 3 –MgO–B 2 O 3 electroslag remelting slag for rack plate steel

Effect of Refining Slag Composition on the Cleanliness of Oriented Silicon Steel

An Innovative CaO–SiO2–MgO-Refining Slag Containing 12 to 16 Mass Pct MgO for Tire Cord Steel

Effect of Silicon–Manganese Deoxidation on Oxygen Content and Inclusions in Molten Steel

Study on the Cleanliness of SWRS82B Hard Wire Steel Refined by Fluorine‐Free Slag with Medium and High Basicity