Abstract:Highlights • Crack-free Ti/Ce co-modified 2195 alloys are manufactured by LPBF. • The grains of composites transform from coarse columnar to fine equiaxed grains. • The crack suppression and strengthening mechanisms of composites are revealed. • The bracket component with lattice structure filling is designed and manufactured. High cracking susceptibility of Al-Li alloys with Ti/CeB 6 addition is thoroughly suppressed in laser powder bed fusion (LPBF) processing of Ti/Ce co-modified 2195 alloys at relatively high scan speeds, while the cracking suppression mechanism and phase formation in these composites are not clarified. In this work, microstructure evolution and mechanical performance of the LPBF-fabricated Ti/Ce co-modified 2195 are investigated to reveal their cracking suppression and strengthening mechanisms. The results show that apparent grain refinement of the composites is ascribed to high supercooling from rapid formation of constitutional supercooling zone in front of solid-liquid interfaces by high- Q -value Ti solute, and heterogeneous nucleation of in situ formed Al 3 Ti and Al 11 Ce 3 precipitates. Their synergistic interactions promote formation of fine equiaxed grains and thus inhibit crack initiation. The composites exhibit high microhardness of 100±5 HV 0.2 , nano-hardness of 1.6±0.1 GPa and elastic modulus of 97±3 GPa, where the elastic modulus increases by ∼27% and ∼31% compared to those of LPBF-processed and conventionally manufactured 2195 alloys, respectively. A tensile strength of ∼336 MPa and an elongation of ∼3% are obtained from in-situ synchrotron X-ray diffraction measurement. The improved properties are derived from grain refinement and Orowan strengthening. Based on the optimal processing parameter and composition, a bracket component filled with lattice structures is designed and manufactured with good manufacturing quality and processing accuracy.

Microstructure Development and Mechanical Properties of Ce-TZP/La- Β-Alumina Composites

Comparison of sintering behavior and reinforcing mechanisms between 3Y-TZP/Al2O3(w) and 12Ce-TZP/Al2O3(w) composites: Combined effects of lanthanide stabilizer and Al2O3 whisker length

Effects of La and Ce on Microstructure and Properties of SiC/Al Composites

Microstructure evolution and mechanical properties strengthening in laser powder bed fusion of high-strength SiC and TiB 2 co-reinforced Al-Zn-Mg-Cu composites

Effects of ZrC content on the microstructure and mechanical property of ZrC/ZTA composites consolidated by hot pressing

Influence of B-site substituent Ce on thermophysical, oxygen diffusion, and mechanical properties of La2Zr2O7

Preparation and mechanical properties of titanium alloy matrix composites reinforced by Ti3AlC and TiC ceramic particulates

Enhanced Mechanical Properties in Ceramic Multilayer Composites Through Integrating Crystallographic Texture and Second-Phase Toughening

Elevated temperature microstructural stability in Al-7Cu-0.5Mn-0.2Zr alloys through Ce addition: Enhanced coherent interfacial stability of cu-rich θ'/α-Al interface

Effect of CeO2 Content on Microstructure and Properties of SiCp/Al-Si Composites Prepared by Powder Metallurgy

Effect of rare earth Ce addition on microstructure and mechanical properties of titanium alloy Ti-6Al-4V

Mechanical properties and low temperature degradation (LTD) of cation-stabilized zirconia

Preparation, mechanical properties, and toughening mechanisms of SiCw/SiCp‐reinforced zirconia‐toughened alumina ceramics

Achieving the synergy of low thermal conductivity and superior mechanical properties of Ce doping La2Zr2O7 ceramics for thermal protection coatings: Experiment and first-principles calculations

Microstructure and Mechanical Properties of an Alumina–glass Low Temperature Co-Fired Ceramic

Facile method for preparing lamellar structured alumina-zirconia ceramics with high toughness

Investigation of Microstructure, Mechanical, and Wear Behavior of Lanthanum Zirconate, Yttrium Zirconate, and Lanthanum Yttrium Zirconate

Stronger and Tougher Nanosized Dense Ceria-Doped Tetragonal Zirconia Polycrystals by Sinter-Hip

Multi-scale investigation of A356 alloy with trace Ce addition processed by laser surface remelting

Laser additive manufacturing of Ti and Ce co-modified 2195 difficult-to-process aluminum alloy: Grain refinement, cracking suppression and enhanced mechanical properties

Effect of Ce/La Microalloying on Microstructural Evolution of Mg-Zn-Ca Alloy During Solution Treatment