Abstract:Electrochemical etching of silicon carbide (SiC) material has received increasing attention in recent years, due to its simple procedure, low cost and significance in the exploration of novel optoelectronic devices. In this paper, 4H-SiC substrates were electrochemically etched at a constant current density of 392.98 mA cm-2 in an electrolyte made up of hydrofluoric acid and deionized water. The layering of a SiC porous layer and periodic fluctuation of the voltage were witnessed for the first time, with the layering phenomenon corresponding well to the voltage period. However, no such phenomenon was observed when the SiC substrates were anodic etched under the same conditions with magnet stirring. As a result, the periodic variation of voltage was hypothesized to be the cause of regular layering during constant current electrochemical etching. Electrochemical etching in potentiostatic mode was thus performed at different voltages. We found that the diameter of the SiC nanopores increased while the thickness of the sidewall decreased with the increasing voltage. Based on the experimental findings, a model of mass transport was proposed. The mass transport process leads to periodic changes in resistance, hence the periodic change in voltage. This successfully explained the reason for the layering. Furthermore, SiC substrates were also electrochemically etched at high and low current densities, finding the existence of a threshold current density for the occurrence of the layering. Energy dispersive x-ray spectroscopy analysis showed that the composition of the SiC porous layer remained unchanged compared to the pure SiC wafer, implying that the peeling-off of the SiC porous layer obtained by electrochemical etching can be directly adopted for use on devices requiring a SiC porous structure.

Influences of Temperature and Etching Voltage on the Surface Morphology of Photo-Electro-Chemical Etching for Silicon Microchannel Arrays

Photo-electrochemical Etching of Macroporous Silicon Arrays Used in Silicon Microchannel Plates

Fabrication of Ordered Macropore Arrays in n-Type Silicon Wafer by Anodic Etching Using Double-Tank Electrochemical Cell

High Anodic-Voltage Focusing of Charge Carriers in Silicon Enables the Etching of Regularly-Arranged Submicrometer Pores at High Density and High Aspect-Ratio

Micro Etching Method Inside Microchannels

Uniform Metal-Assisted Chemical Etching for Ultra-High-Aspect-Ratio Microstructures on Silicon

Flow-restricted Etching Method on Isotropic Substrates and Its Mechanism

Dimensional Constraints on High Aspect Ratio Silicon Microstructures Fabricated by HF Photoelectrochemical Etching

Study on the layering phenomenon of SiC porous layer fabricated by constant current electrochemical etching

Demonstration of Irradiation-Resistant 4H-Sic Based Photoelectrochemical Water Splitting

High-aspect ratio micro- and nanostructures enabled by photo-electrochemical etching for sensing and energy harvesting applications

High Aspect Ratio Si Etching Technique and Application

Selective etching of n-type silicon in pn junction structure in hydrofluoric acid and its application in silicon nanowire fabrication.

Electrochemically Etched Pore Array in Silicon with Large Spacing and High-Aspect-ratio

Anisotropic Etching of Three-Dimensional Shapes in Silicon - the Important Role of Galvanic Interaction

Anisotropic Charge Transport Enabling High‐Throughput and High‐Aspect‐Ratio Wet Etching of Silicon Carbide (Small Methods 8/2022)

Wafer level microarcing model in 90nm chemical-vapor deposition low-k via etch on 300mm silicon-on-insulator substrate

Research on Silicon Wafer Surface Phase under the Ultra-thin Slicing Process and Its Etching Hindrance Behavior during Metal-Assisted Chemical Etching

Wafer-Scale Fabrication of Ultra-High Aspect Ratio, Microscale Silicon Structures with Smooth Sidewalls Using Metal Assisted Chemical Etching

Influence Of Anodization Current Density On Preparation And Corrosion Of N-Type Macroporous Silicon In 1.0 M Naoh

A wet process to etch arrayed vias for through silicon via application of 3D packaging