Abstract:Property and behaviour of sand–pile interface are crucial to shaft resistance of piles. Dilation or contraction of the interface soil induces change in normal stress, which in turn influences the shear stress mobilised at the interface. Although previous studies have demonstrated this mechanism by laboratory tests and numerical simulations, the interface responses are not analysed systematically in terms of soil state (i.e. density and stress level). The objective of this study is to understand and quantify any increase in normal stress of different pile–soil interfaces when they are subjected to loading and stress relief. Distinct element modelling was carried out. Input parameters and modelling procedure were verified by experimental data from laboratory element tests. Parametric simulations of shearbox tests were conducted under the constant normal stiffness, constant normal load and constant volume boundary conditions. Key parameters including initial normal stress (\( \sigma_{{{\text{n}}0}}^{\prime } \)), initial void ratio (e 0), normal stiffness constraining the interface and loading–unloading stress history were investigated. It is shown that mobilised stress ratio (\( \tau /\sigma_{\text{n}}^{\prime } \)) and normal stress increment (\( \Updelta \sigma_{\text{n}}^{\prime } \)) on a given interface are governed by \( \sigma_{{{\text{n}}0}}^{\prime } \) and e 0. An increase in \( \sigma_{{{\text{n}}0}}^{\prime } \) from 100 to 400 kPa leads to a 30 % reduction in \( \Updelta \sigma_{\text{n}}^{\prime } \). An increase in e 0 from 0.18 to 0.30 reduces \( \Updelta \sigma_{\text{n}}^{\prime } \) by more than 90 %, and therefore, shaft resistance is much lower for piles in loose sands. A unique relationship between \( \Updelta \sigma_{\text{n}}^{\prime } \) and normal stiffness is established for different soil states. It can be applied to assess the shaft resistance of piles in soils with different densities and subjected to loading and stress relief. Fairly good agreement is obtained between the calculated shaft resistance based on the proposed relationship and the measured results in centrifuge model tests.

The Dilatant Behaviour of Sand–pile Interface Subjected to Loading and Stress Relief

Large Deformation Analysis of Intermittent Pile Penetration into Dense Sand Incorporating a State Dependent Mohr–Coulomb Model

Stresses Developed Around Displacement Piles Penetration in Sand

Large-Deformation Finite-Element Simulation of Deformation and Strain Fields Resulting from Closed-End Displacement Pile Installation in Sand

Theoretical Breakage Mechanics and Experimental Assessment of Stresses Surrounding Piles Penetrating into Dense Silica Sand

Sand Grain Crushing and Interface Shearing During Displacement Pile Installation in Sand

Advanced laboratory investigation of axial cyclic loading in silica sands

DEM Study of the Stress Fields Around the Closed-Ended Displacement Pile Driven in Sand

Large Deformation Finite-Element Simulation of Displacement-Pile Installation Experiments in Sand

Soil-pile interaction on an instrumented pile under cyclic axial loads in sand

Effect of Loading Rate on Lateral Pile-Soil Interaction in Sand Considering Partially Drained Condition

Performance of laterally loaded H-piles in sand

Field and Model Investigations into the Influence of Age on Axial Capacity of Displacement Piles in Silica Sands

Centrifuge Model Tests on Laterally Loaded Piles in Sand

Sand-Steel Interface Behaviour Under Large-Displacement And Cyclic Shear

Behavior of Sand Filled Nodular Piles under Compression in Soft Soil Areas

Quantifying the Influence of Pile Diameter on the Load Transfer Curves of Laterally Loaded Monopile in Sand

Effect of Cyclic Jacking on Sand-Pile Interface Shear Behaviour

A Destructive Field Study on the Behavior of Pile under Ten

Ultimate Soil Resistance of the Laterally Loaded Pile in Uniform Sand

Influence of the Penetration of Adjacent X-section Cast-in-place Concrete (XCC) Pile on the Existing XCC Pile in Sand