Abstract:High thermoelectric cooling efficiency requires a high average ZT value, especially in a low temperature range. PbTe-based compounds are typical intermediate-temperature thermoelectric materials due to their relatively low ZT values near room temperature. Here, we attempt to enhance the average ZT value of PbTe, especially at 300–600 K, through decreasing its band gap so as to evaluate the thermoelectric cooling performance. The results show that Sn alloying in PbTe can narrow its band gap from ∼0.28 to ∼0.18 eV, which shifts its peak power factor from 673 to 523 K. Combining the enhanced power factor with the reduced lattice thermal conductivity after Sn alloying, a maximum average ZT value of ∼0.74 is obtained in n-type Pb0.785Sn0.2Sb0.015Te at 300–723 K. Finally, the thermoelectric cooling performance of a Pb0.785Sn0.2Sb0.015Te-based single leg is measured, and a cooling ΔTmax of ∼15 K is realized. These results demonstrate that, after tuning the band gap, PbTe can also exhibit promising cooling performance even though it is a typical intermediate-temperature thermoelectric material.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.1c02589.Experimental details; powder XRD patterns; lattice parameters; measured density; heat capacity; carrier mobility; thermal diffusivity; Lorenz number; size of single-leg samples; bipolar thermal conductivity; and thermoelectric cooling performance of the samples in this study (PDF)This article has not yet been cited by other publications.

Enhanced Low Temperature Thermoelectric Performance and Weakly Temperature-Dependent Figure-of-merit Values of PbTe–PbSe Solid Solutions

Enhanced thermoelectric performance of n -type PbTe bulk materials fabricated by semisolid powder processing

Enhanced thermoelectric performance of n-type PbTe through introducing PbSe by a fast preparation method

Improved Thermoelectric Properties of Bi2Te3−xSexalloys by Melt Spinning and Resistance Pressing Sintering

Enhanced Thermoelectric Performance of Ag0.8Pb18SbTe20 Alloyed with Se

Enhanced thermoelectric performance of PbTe bulk materials with figure of merit zT >2 by multi-functional alloying

Thermoelectric Properties of PbTe1−Se Alloys Prepared by High Pressure

Thermoelectric Properties of PbSe-PbS Solid Solutions Prepared by Mechanical Alloying Method and High Pressure Sintering

High Thermoelectric Performance of Ge1−xPbxSe0.5Te0.5 Due to (pb, Se) Co-Doping

Thermopower enhancement in Pb 1− x Mn x Te alloys and its effect on thermoelectric efficiency

Electronic structure and thermoelectric properties of PbTe1−xSex from first-principles calculations

Boosting Thermoelectric Performance of PbBi2Te4 Via Reduced Carrier Scattering and Intensified Phonon Scattering.

Extremely Low Thermal Conductivity in Thermoelectric Ge0.55Pb0.45Te Solid Solutions via Se Substitution

Electrical and thermal transport properties of Pb1-xSnxSe solid solution thermoelectric materials.

Enhanced Thermoelectric Performance of PbSe Co-Doped with Ag and Sb

Melt-slow Cooling Synthesis and Thermoelectric Properties of Pb9.6SbmTe3Se7 Alloys

Thermoelectric enhancement at low temperature in nonstoichiometric lead-telluride compounds

Enhancing Thermoelectric Performance of p-Type PbSe through Suppressing Electronic Thermal Transports

Evaluation on the Thermoelectric Cooling Ability of PbTe

Thermoelectric Transport Properties of Pb–Sn–Te–Se System

Integrating Band Structure Engineering with All‐Scale Hierarchical Structuring for High Thermoelectric Performance in PbTe System