Abstract:Ni3Al-based alloy fabricated by twin wire and arc additive manufacturing exhibited periodic remelting bands (RB) with unique microstructural characteristics. In this work, the deposited Ni3Al-based alloy was oxidized at 1100 °C for different times to investigate the high-temperature oxidation difference caused by RB. The differences in the microstructure, grain orientation, oxidation behavior, and oxidation mechanism between RB and non-RB were systematically studied. The results showed that these RB, epitaxially grown on the non-RB during each deposition layer, displayed similar Goss textures but a higher proportion of γ + γ′ dual-phase microstructure compared to non-RB. The oxidation of the deposited Ni3Al-based alloy obeyed parabolic growth kinetics at 1100 °C for 10 h and the oxidation scales were consisted of external NiO layer, intermediate NiAl2O4 layer with dispersed Al2O3 and TiO2 particles and internal Al2O3 layer. The outward diffusion of Al and Ti elements during the oxidation process led to the decomposition of γ′ precipitations and the formation of γ′-reduced layer beneath the Al2O3 layer. The cross-section microstructure of oxidation scales indicated that the RB displayed thicker scales and poorer oxidation resistance than non-RB. The oxidation rate of the deposited Ni3Al-based alloy was controlled by the outward transport rate of the total cations (Ni2+, Al3+, and Ti4+) through the Al2O3 layer. Initial oxidation and diffusion interface analysis demonstrated that the γ + γ′ dual-phase had a higher outward transport rate of the cations, which was responsible for the thicker oxide scales on the RB.

Effect of Platinum Addition on Oxidation Behaviour of Γ/γ′ Nickel Aluminide

Mechanical Properties and Oxidation Characteristics of TiNiAl(Nb) Intermetallics

Diffusion Characteristics and Structural Stability of Pt Modified Β-Nial/γ′-ni3al Within NiCoCrAl Alloy at High Temperature

Improving Cyclic Oxidation Resistance of Ni3Al-based Single Crystal Superalloy with Low-Diffusion Platinum-Modified Aluminide Coating

Influence of Pt on oxidation behavior of CoNiCrAlY alloy

The Effects of Alloying Elements Cr, Al, and Si on Oxidation Behaviors of Ni-Based Superalloys

Effects of Reactive Element Oxides on the Isothermal Oxidation of Β-Nial Coatings Fabricated by Spark Plasma Sintering

Effect of Pt on Stress Rupture Properties of Pt-Modified Nickel Aluminide Coatings at 1100 °C

Microstructural Study on Oxidation Resistance of Nonmodified and Platinum Modified Aluminide Coating

Effect of Nickel Aluminide Microcrystalline Coating on High-Temperature Oxidation Behavior of NiAl-33.5%Cr-0.5%Zr Alloy

Modification of NiCoCrAlY with Pt: Part I. Effect of Pt Depositing Location and Cyclic Oxidation Performance

Effect of aluminisation characteristics on the microstructure of single phase β-(Ni,Pt)Al coating and the isothermal oxidation behaviour

Early oxidation behavior of Ti50Al and Ti45Al8Nb alloys

The high-temperature oxidation behavior and mechanism in a powder metallurgy Ni-based superalloy featuring δ-Nb3Al addition

Microstructure Analysis of Initial Alumina of Pt-Modified Aluminide Coatings on Ni-Based Alloy

Investigation of Pt-Dy Co-Doping Effects on Isothermal Oxidation Behavior of (Co,ni)-Based Alloy

High-temperature performance of Pt-modified Ni-20Co-28Cr-10Al-0.5Y coating: Formation mechanism of Pt-rich overlayer and its effect on thermally grown oxide failure

A novel single-phase γ′ nanocrystalline coating with high resistance to oxidation and scale rumpling yet mitigated interdiffusion with the alloy substrate

Oxidation Behaviour of New Nickel-Base Superalloys with Varying Aluminium: Niobium Ratio

Non-uniform high-temperature oxidation behavior of twin wire and arc additive manufactured Ni3Al-based alloy

On the effect of Ti on Oxidation Behaviour of a Polycrystalline Nickel-based Superalloy