Electrical Characteristics of Multilayer MoS2 Transistors at Real Operating Temperatures and Different Ambient Conditions
Hyuk‐Jun Kwon,Jaewon Jang,Hongki Kang,Sunkook Kim,Vivek Subramanian,Costas P. Grigoropoulos
DOI: https://doi.org/10.1149/ma2014-02/44/2106
2014-01-01
Abstract:Two-dimensional (2D) materials have been giving a chance to advance high performance electronic technology for next generation nanoelectronics devices. Among 2D materials, molybdenum disulfide (MoS 2 ) is drawing attention due to its relative large bandgap (1.3-1.8 eV) and the 50~200 cm 2 /V·S range of high carrier mobility at room temperature. In the few early report, multilayer MoS 2 could have been much better than single-layer MoS 2 because it has larger density of state (DOS) and helps to create multiple conducting channels by field effect, which will lead to boost the current drive of TFTs. At realistic operating temperatures, however, the carrier transport mechanism of these 2D layered MoS 2 FETs has not yet been intensively explored for use in electronics. Therefore, we investigate carrier transport and the impact of the operating ambient conditions on back-gated multilayer MoS 2 field-effect transistors with a thickness of ~50 nm at their realistic working temperatures and under different ambient conditions (in air and in a vacuum of ~10 -5 Torr). Moreover, we examine the quality of the device interface and an energy distribution of carrier trapping/scattering sites through the low-frequency noise (LFN) measurement. A Schottky barrier of ~65 meV was formed between the Ti/Au metal contact and the MoS 2 semiconductor and the barrier partially hindered the flow of carriers. However, when the operating temperature increased, the carriers easily overcame the barrier by thermionic emission at defects. This caused I min to rise as shown in Fig. 1(a) and (b). However, at high V GS (blue region), the drain current decreased slightly as the operating temperatures increased. This is consistent with phonon scattering which is inversely proportional to the operating temperature. Fig. 2(a) shows that V TH shifts toward the negative direction as the temperature increases. This behavior is observed due to an increase in thermally generated carriers, resulting in a shift in the Fermi level in the semiconductor. Additionally, V TH was higher in air than in a vacuum. One possible explanation is that the oxygen and water molecules on the surface of MoS 2 semiconductors could be adsorbed from the ambient air, and they could trap the charge carriers from the conduction band. This could make depleted channels and induce a positive threshold voltage shift. Also, the chemisorption on the MoS 2 flake created defects and associated increased scattering which causes a reduction in μ eff , unlike in a vacuum (Fig. 2(b)). However, thick multilayer MoS 2 was less affected by the ambient conditions, because the thickness of the MoS 2 layers suppressed interactions with the underlying channel. This fact was also supported negligible effects of ambient conditions on interface quality as determined by sub-threshold slope values (Fig. 2(a)). In Fig. 3 (a), obtained exponent values ( γ ) from low-frequency noise analysis, 1/f γ , exhibited the increase of γ at low gate bias range due to active slow traps. And the slow traps were filled and thus γ decreased and saturated to near 1 (0.95) as V G increased. In addition, the Hooge’s parameter, α H , was extremely large in the subthreshold region and drastically decreased as the gate bias increased until it matched V th . This result also supports that the amount of active traps which cause the carrier number fluctuation decreases more significantly below V th since the increased gate bias fills traps; it agrees with the change of the exponent value aforementioned. It is also interesting fact that the Hooge’s parameter (measured in ambient conditions) during fully ON regime is on the order of 10 -2 . This value is comparable to that observed in single-layer MoS 2 FETs measured under vacuum conditions. This result provides multilayer structures more robust than single-layer for the effect of surface adsorbates in air and is consistent with our previous statement mentioned above.