Abstract:A wideband low-noise amplifier (LNA) featuring transformer-based wideband input matching is proposed for millimeter-wave applications. By analyzing the properties of conventional series input matching networks, which were widely employed in narrowband LNAs and shunt-series matching networks for bandwidth extension, a novel input matching network possessing the merits of both was proposed. For further bandwidth extension, another peak of input impedance at a higher frequency is introduced for the proposed input matching network. Moreover, it is proved that the proposed input matching network can suppress the gate resistor noise, resulting in significant noise figure (NF) improvement of an LNA. On the other hand, the NF is further reduced by connecting a transformer between the two amplification stages, which helps suppress the noise contribution from the second stage, leading to an LNA design with NF lower than 4.5 dB over a very wide operating bandwidth. To enhance the gain bandwidth, the peak distribution, including both shunt peaking and series peaking, is discussed. By appropriately distributing these peaks, which is also known as the pole-tuning technique, a wider gain bandwidth can be obtained. To validate the proposed techniques, an LNA with two common-source (CS) stages is designed and fabricated using a 65-nm CMOS process, and the overall chip size, including all pads, is only 0.26 mm². The two CS stages are cascoded for dc biasing to reduce the power consumption. Experimental results show that a peak gain of 13.5 dB is achieved within a -3-dB bandwidth from 19.2 to 42.6 GHz. The measured NF is 3.1-4.5 dB, and the input 1-dB gain compression point (IP1 dB) ranges from -13.54 to -9.89 dBm in the entire gain bandwidth. The input return loss S₁₁ is less than -10 dB over a frequency range of 16.8-38.9 GHz. Moreover, benefiting from the current-reuse technique, the power consumption of the LNA is only 6.36-mW.

Design of a Fully Integrated Switchable Transistor CMOS LNA for 2.1 / 2.4 GHz Application

Analysis and Design of Ultra-Wideband Low-Noise Amplifier with Input/Output Bandwidth Optimization and Single-Ended/Differential-Input Reconfigurability.

A 1 V Switchable CMOS LNA for 802.11A/B WLAN Applications

A Compact 2.1–39 GHz Self-Biased Low-Noise Amplifier in 65 Nm CMOS Technology

3-10 GHz self-biased resistive-feedback lna with inductive source degeneration

A fully integrated 0.18-/spl mu/m CMOS low noise amplifier for 2.4-GHz applications

A 0.9/1.8/2.4Ghz-Reconfigurable LNA with Inductor and Capacitor Tuning for IoT Application in 65nm CMOS

A dual-band 2.1GHz/5.2GHz LNA for reconfigurable radio

A High Gain Fully Integrated CMOS LNA for WLAN and Bluetooth Application

A Switchable Dual-Band LNA with Simultaneous Noise and Input Impedance Matching for GSM/TD-SCDMA Applications

A 2.1–2.5 GHz high linearity and low noise down-conversion active mixer

A dual band CMOS two-stage variable gain low noise amplifier

A LOW POWER, HIGH-LINEARITY CMOS DOWNCONVERSION FOLDED MIXER FOR 2.4GHz ISM BAND APPLICATIONS

A 0.1-4Ghz Reconfigurable Multi-band CMOS LNA for SDR Applications

Inductorless CMOS Low Noise Amplifier for Multiband Application in 0.1–1.2 GHz

A Fully Integrated 0.18-Mu M Cmos Low Noise Amplifier for 2.4-Ghz Applications

Process Variation Compensation of a 2.4GHz LNA in 0.18um CMOS Using Digitally Switchable Capacitance.

Ultralow Noise Figure and Broadband CMOS LNA With Three-Winding Transformer and Large Transistor

A Wideband CMOS LNA Using Transformer-Based Input Matching and Pole-Tuning Technique

A Broadband CMOS LNA for WLAN Applications

A CMOS 0.5&#x2013;10.6 GHz Inductor Feedback Low Noise Amplifier for Multi-Standard Application