Abstract:This paper displays a voltage-controlled oscillator (VCO) with high performance implemented in 0.18 μm CMOS. The proposed CMOS VCO adopts a current-reused method, analog coarse and fine tuning mechanisms, and an adaptive overdrive voltage control structure to increase the overall performance, such as the power dissipation, phase noise, and tuning range, and has a robust start-up condition. The current-reused complementary structure with higher transistor transconductances is to save power consumption; the analog coarse and fine tuning mechanisms are to effectively widen the tuning range; and the adaptive overdrive voltage control technique is to change the transconductances of the transistors to improve power consumption by reasonably biasing the gate and body terminals in a class-AB mode to adjust the threshold voltage of the NMOS transistors. The proposed CMOS VCO adopts the class-AB mode to improve the overall performance and the start-up condition. The figure-of-merit (FOM) and FOM with tuning range (FOMT) are used in evaluating the CMOS VCO performance. The measured phase noise at 1 MHz and 10 MHz offsets is –130.34 dBc/Hz and –150.96 dBc/Hz at the 3.38 GHz operating frequency, respectively. The proposed CMOS VCO has a tuning range between 2.85 and 3.62 GHz corresponding to 23.8% for the fifth-generation (5G) wireless communication applications. The proposed CMOS VCO core using a 1.4-V supply consumes 7.5 mW DC power. The FOMs and FOMTs at 1- and 10-MHz offsets are −192.2, −192.8, −199.7, and −200.3 dBc/Hz, respectively, from the 3.38 GHz output frequency.

A Tail-Feedback VCO with Self-Adjusting Current Modulation Scheme

A Tail-Current Modulated VCO with Adaptive-Bias Scheme

A Feedback Class-C VCO with Robust Startup Condition over PVT Variations and Enhanced Oscillation Swing

A Constant-Current-controlled Class-C VCO Using a Self-Adjusting Replica Biasing Scheme

A 92 Fsrms Jitter Frequency Synthesizer Based on a Multicore Class-C Voltage-Controlled Oscillator with Digital Automatic Amplitude Control

A 40 Nm Cmos V-Band Vco with On-Chip Body Bias Voltage Control Technique

A current-reuse Class-C LC-VCO with an adaptive bias scheme

A 3.7-Mw $K$ -Band Dual-Feedbacks VCO Employing a Self-Inversed Transformer with 190-Dbc/hz FOM

An Inverted Complementary Cross-Coupled VCO to Reduce Phase Noise Sensitivity to KVCO

A Pvt-Robust Feedback Class-C Vco Using an Oscillation Swing Enhancement Technique

A Wideband Voltage-Controlled Oscillator with Gain Linearized Varactor Bank

An Improved Low Phase Noise LC-VCO with Wide Frequency Tuning Range Used in CPPLL

Class-C VCO with Amplitude Feedback Loop for Robust Start-Up and Enhanced Oscillation Swing

A Complementary Oscillator Using a Current-Limiting Tail Resistor in 180nm CMOS

A Constant-Current-Controlled Class-C Voltage-Controlled Oscillator Using Self-Adjusting Replica Bias Circuit

A Low Noise VCO with Common-Tail Inductor in 180nm CMOS Technology

A HIGH-SWING CLASS-C VCO WITH AMPLITUDE FEEDBACK LOOP FOR LOW PHASE NOISE AND ROBUST START-UP

A Uniform Phase Noise QVCO with a Feedback Current Source

CMOS Voltage-Controlled Oscillator with Complementary and Adaptive Overdrive Voltage Control Structures

A Swing-Enhanced Current-Reuse Class-C VCO with Dynamic Bias Control Circuits

A 24ghz Low Phase Noise Feedback Cmos Lc-Vco