Abstract:This study presents a fabrication strategy for 3D carbon microstructures using via two-photon vat photopolymerization (2p-VPP) and susceptor-assisted microwave pyrolysis (SMWP). Fabricating carbon-based electrode materials with miniaturized functional structures is pivotal for developing high-performance electrochemical microdevices. However, efficiently producing these structures in the submicron regime with desired materials is still challenging. To address this, a hybrid microfabrication strategy was developed, and 3D carbon-based microstructures with submicron resolution were successfully produced. A carbon nanotube nanocomposite photoresist (SCNT-PR1) with improved dispersibility was first prepared. After a comprehensive printability assessment, 3D microstructures with a resolution of 833 ± 54 nm were produced using 2p-VPP. Through SMWP, the microstructures were transformed into pyrolytic carbon (PyC) nanocomposite microstructures with retained geometrical features. SMWP was shown to produce PyC with a less disordered carbon atomic structure, thanks to the accelerated pyrolysis reaction under MW irradiation, when compared to pyrolysis using a conventional furnace. The resistivity was reduced by over 75% from 0.69 ± 0.13 Ω cm to 0.16 ± 0.01 Ω cm, and enhanced electrochemical performance was confirmed. The fabricated PyC nanocomposite showed a further 12% reduction in electrical resistivity and a 20% lower charge transfer resistance for the redox reaction when using SCNT-PR1 as the precursor. Overall, this hybrid fabrication strategy demonstrates the advantages of producing 3D carbon microstructures with precise control over the geometric features and enhancing electrical and electrochemical properties compared to the conventional pyrolysis method. Its potential could be extended to the fabrication of miniaturized electrochemical devices, including microelectronics and point-of-care devices.

A Novel Experimental Approach to Compatible Carbon Nanofiber Diffusion Around Circular Carbon Micro-Post Surfaces

A Novel Approach to Fabricate Three-Dimensional Carbon-Based Interconnect for Micro/nano Optoelectronic Integration

A novel approach to fabricate 3-dimensional carbon-based interconnect for micro/nano optoelectronic integration

Fabrication of CNT-carbon composite microstructures using Si micromolding and pyrolysis

Carbon Microstructure with High Aspect Ratio Fabricated by Novel Method of Photolithography and Pyrolysis

Carbon Nanotube Integrated 3-Dimensional Carbon Microelectrode Array by Modified SU-8 Photoresist Photolithography and Pyrolysis

Integrating Vertically Aligned Carbon Nanotubes on Micromechanical Structures

Growth of Nano-Wrinkles on Photoresist-Derived Carbon Microelectrode Array

Nanoimprint Lithography for Next-Generation Carbon Nanotube-Based Devices

Fabrication and electrical integration of robust carbon nanotube micropillars by self-directed elastocapillary densification

Fabrication of Micro/Nanotubes by Mask-Based Diffraction Lithography

Fabrication of High Aspect Ratio Carbon Nanotube-Carbon Composite Microstructures Based on Silicon Molding Technique

A New Strategy to Prepare Carbon Nanotube Thin Film by the Combination of Top-Down and Bottom-Up Approaches

Fabrication of predesigned 3D carbon based microstructures via two-photon vat photopolymerization and susceptor-assisted microwave post-processing

Multilevel, Multicomponent Microarchitectures of Vertically-Aligned Carbon Nanotubes for Diverse Applications

Carbon nanotube nanoelectronic devices compatible with transmission electron microscopy.

Scalable fabrication of carbon-based MEMS/NEMS and their applications: a review

Development of Microsturcture Based on Single-Wall Carbon Nanotube.

Metal-catalyst Free Integration of SiO2 Nanowires into Carbon MEMS

Fast and Controlled Integration of Carbon Nanotubes into Microstructures

An Optimized Process for Fabrication of High-Aspect-Ratio Photoresist-Derived Carbon Microelectrode Array on Silicon Substrate