Abstract:This study reports the synthesis of Ni-Co-SiC coatings onto Q235A steel substrates through magnetic-field-induced electrodeposition to improve the surface performances of the machine parts. The microstructure, topology, roughness, corrosion, and wear resistances of the coatings were investigated through X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), atomic force microscopy (AFM), hardness testing, electrochemical analysis, and friction wear testing, respectively. The Ni-Co-SiC coating deposited at 0.4 T (MS1) with a perpendicular magnetic direction showed the maximum SiC content and NiCo grain size (86.5 nm). The surface topology was also fine, dense, and smooth. In addition to that, the images obtained from the AFM characterization showed that the surface roughness of the MS1 coating was 76 nm, which was significantly lower compared to the roughness observed in Ni-Co-SiC coatings fabricated under the magnetic induction of 0 T (MS0) and magnetic field applied in a parallel direction to 0.4 T (MS2). The XRD results revealed that the preferential growth direction of the NiCo grains was changed from the (200) crystal plane to the (111) plane with the introduction of a perpendicular magnetic field. Moreover, MS2, MS1, and MS0 had thickness values of 25.3, 26.7, and 26.3 μm, respectively. Among all the coatings, MS1 showed the lowest friction coefficient and the highest hardness value (914.8 HV), suggesting enhanced wear resistance. Moreover, the MS1 coating revealed a maximum corrosion potential of −257 mV, and the lowest corrosion current of 0.487 μA/cm2, suggesting its improved corrosion resistance.

Enhanced Saturation Magnetization of Nanocrystalline Cobalt Produced by Surface Mechanical Attrition Treatment

Strain-induced Refinement and Thermal Stability of a Nanocrystalline Steel Produced by Surface Mechanical Attritiontreatment

Nanocrystallization and Magnetic Properties of Fe-30 Weight Percent Ni Alloy by Surface Mechanical Attrition Treatment

Microwave Frequency Performance and High Magnetic Anisotropy of Nanocrystalline Fe<SUB>70</SUB>Co<SUB>30</SUB>-B Films Prepared by Composition Gradient Sputtering

Magnetic Property of Nanocrystalline Nickel Prepared by Surface Mechanical Attrition Treatment

Diffusion Phenomenon During SMAT and Its Effect on Magnetic Property in Nanocrystalline Fe-30 Wt%ni Alloy

A Coupled EBSD/TEM Analysis of the Microstructure Evolution of a Gradient Nanostructured Ferritic/Martensitic Steel Subjected to Surface Mechanical Attrition Treatment

Interdiffusion of Alloying Elements in Nanocrystalline Fe–30 Wt.% Ni Alloy During Surface Mechanical Attrition Treatment and Its Effect on Α → Γ Transformation

Effect of surface mechanical attrition treatment on the microstructure of cobalt–chromium–molybdenum biomedical alloy

EFFECT OF SURFACE NANOCRYSTALLIZATION ONMICROSTRUCTURE AND THERMAL STABILITYOF REDUCED ACTIVATION STEEL

Microstructural Characterization of Nanocrystalline Nickel Produced by Surface Mechanical Attrition Treatment

High-temperature surface alloying of nanocrystalline nickel produced by surface mechanical attrition treatment

Surface Nanocrystallization of Mg-3 Wt.% Li-6 Wt.% Al Alloy by Surface Mechanical Attrition Treatment

Crystallization Kinetics of Co-Finemet Amorphous Alloys and Magnetic Properties of Nanocrystalline Powder Cores

Pulsed Magnetic Treatment of Cobalt for Enhanced Microstructures and Mechanical Properties

Microstructure and Thermal Stability of Bulk Nanocrystalline Alloys Produced by Surface Mechanical Attrition Treatment

Measurement of Microstructural Parameters of Nanocrystalline Fe–30 Wt.%ni Alloy Produced by Surface Mechanical Attrition Treatment

Thermal Stability in Nanocrystalline Fe-30 Wt Pct Ni Alloy Induced by Surface Mechanical Attrition Treatment

Synthesis of nanocrystalline intermetallic layer by mechanical attrition

Impact of Magnetic Field Direction on Performance and Structure of Ni-Co-SiC Coatings Fabricated via Magnetic-Field-Induced Electrodeposition

Microstructure, crystallization behavior, and soft magnetic properties of Co-doped Finemet-type nanocrystalline alloys