Abstract:In this work, nanocrystalline W–Al alloys (up to 20 at.% of Al) were produced by high energy ball milling and powder microstructural evolution was investigated as a function of milling time. It was found that, regardless of the composition, alloys crystallite size progressively decreases and stabilizes around a value of about 10–15 nm after 70–100 h of mechanical treatment. The aluminum dissolution into the bcc W lattice was confirmed by DSC, SEM, and TEM. The formation of intermetallic compounds was detected neither during ball milling nor after thermal treatments up to 1450 °C. Sintering behavior of mechanically alloyed W–Al alloys was tested under pressureless conditions, and a significant improvement in terms of sinterability with respect to pure W was observed. Along with favoring the sintering process, the addition of Al also resulted in a notable enhancement of the coarsening resistance. Indeed, the analysis of ball-milled pure tungsten after thermal treatment at 1450 °C provided an estimated average crystallite size of about 2 μm, while W80Al20 and W90Al10 alloys retained an average crystallite size of about 70 nm and 60 nm, respectively. Although further work is required to optimize sintering conditions for achieving full density samples, the retaining of the nanostructure marks a significant advancement in the field of W-based alloys.

Surface Nanocrystallization of Mg-3 Wt.% Li-6 Wt.% Al Alloy by Surface Mechanical Attrition Treatment

Strain-induced Refinement and Thermal Stability of a Nanocrystalline Steel Produced by Surface Mechanical Attritiontreatment

Microstructural evolution of AZ31 Mg alloy with surface mechanical attrition treatment: Grain and texture gradient

Microstructure Evolution and Mechanical Properties of an Mg–Gd Alloy Subjected to Surface Mechanical Attrition Treatment

Nanocrystallization and Magnetic Properties of Fe-30 Weight Percent Ni Alloy by Surface Mechanical Attrition Treatment

Measurement of Microstructural Parameters of Nanocrystalline Fe–30 Wt.%ni Alloy Produced by Surface Mechanical Attrition Treatment

High-temperature surface alloying of nanocrystalline nickel produced by surface mechanical attrition treatment

Nanocrystallization and Martensitic Transformation in Fe–23.4Mn–6.5Si–5.1Cr (wt.%) Alloy by Surface Mechanical Attrition Treatment

Microstructure and Thermal Stability of Bulk Nanocrystalline Alloys Produced by Surface Mechanical Attrition Treatment

Interdiffusion of Alloying Elements in Nanocrystalline Fe–30 Wt.% Ni Alloy During Surface Mechanical Attrition Treatment and Its Effect on Α → Γ Transformation

Surface Nanocrystallization of Zircaloy-4 by Surface Mechanical Attrition Treatment

Deformation Mechanism and Dynamic Precipitation in a Mg-7Al-2Sn Alloy Processed by Surface Mechanical Attrition Treatment

Effect of Surface Mechanical Attrition Treatment on Biodegradable Mg-1Ca Alloy.

Precipitation Behavior of Bulk Nanocrystalline GW103K Alloy Induced by Surface Mechanical Attrition Treatment

Wear Behavior of Nanocrystalline Structured Magnesium Alloy Induced by Surface Mechanical Attrition Treatment

Thermal Stability in Nanocrystalline Fe-30 Wt Pct Ni Alloy Induced by Surface Mechanical Attrition Treatment

Microstructural Characterization of Nanocrystalline Nickel Produced by Surface Mechanical Attrition Treatment

Fabrication of nanocrystalline supersaturated W–Al alloys with enhanced thermal stability and high sinterability

Surface Nanocrystallization of Ti–45Al–7Nb–0.3W Intermetallics Induced by Surface Mechanical Grinding Treatment

High-strength GWZ1031K alloy with gradient structure induced by surface mechanical attrition treatment

Nanocrystallization of Zirconium Subjected to Surface Mechanical Attrition Treatment