Abstract:The design progress of the Radio Frequency Quadrupole (RFQ) accelerator for the Compact Pulsed Hadron Source (CPHS) at Tsinghua University is presented in this paper. The RFQ will accelerate protons from 50 keV to 3 MeV, with the RF frequency of 325 MHz. The objective is to obtain the optimum structure of the RFQ accelerator with high transmission rate and tolerable total length. The beam dynamics are studied by the simulation of the proton beam in the RFQ accelerator with the code of PARMTEQM. The output proton beam from the RFQ is well matched into the DTL without Medium-Energy-Beam-Transport (MEBT) between the RFQ and DTL. INTRODUCTION A 325 MHz Radio Frequency Quadrupole (RFQ) accelerator will be built to produce 50mA of proton beam at 3 MeV as an injector of the 13 MeV DTL for the Compact Pulsed Hadron Source (CPHS) project at Tsinghua University. The CPHS project is a universitybased proton accelerator platform (13 MeV, 16 kW, peak current 50 mA, 0.5 ms pulse width at 50 Hz) for multidisciplinary neutron and proton applications [1]. The RFQ system consists of three four-vane resonant cavity sections, one power coupler, 47 slug tuners, 8 dipole-mode stabilizer rods, the RF power supply and its low-level control, vacuum, water cooling, resonance control, beam diagnostics, support and alignment systems. Fig. 1 shows the sketch of the RFQ system and the design parameters are listed in Table 1. Figure 1: Sketch of the 3 MeV RFQ for the CPHS project. To save space and cost, no Medium-Energy-BeamTransport (MEBT) will be placed between the RFQ and DTL. The RFQ is carefully designed to match the beam from the high-energy end of the RFQ to the entrance of the DTL, by reducing the focusing in the exit of the RFQ. The cavity cross section and vane-tip geometry are tailored as a function of longitudinal position. The physics design has been completed. One test section made by aluminium has been machined to verify the capability of the numerically controlled milling machine. The final RFQ cavity is now under construction. This paper summarizes the current physics and mechanical design of the CPHS RFQ and presents the fabrication status of the test section. Table 1: Design Parameters of the CPHS RFQ Parameters Value Unit

R&d of pku single spoke cavity

Design of a 450 MHz Β = 0.2 Single Spoke Cavity at PKU

A Preliminary Quadrupole Asymmetry Study of a Β=0.12 Superconducting Single Spoke Cavity

Design of a ββ = 0.45, f = 350 MHz Spoke Cavity

Design of the CPHS RFQ Linac at Tsinghua University

Design Of A Beta=0.45, F=350 Mhz Spoke Cavity

Cavity BPM Design for PKU-FEL Injector

Mechanical Properties of 3+1/2 Cavity of PKU Photo-Injector

The pku terahertz facility at peking university *

Electromagnetic Design and Beam Dynamics Simulation of a New Superconducting Accelerating Structure for Extremely Low Β Protons

Development of a Prototype Niobium SRF Cavity for the PEFP Proton Superconducting Linac

Design of a 162.5 MHz Superconducting Radio-Frequency Quadrupole for High-Intensity Proton Acceleration

The Radio-Frequency Design of an Iris-Type Coupler for the CPHS Radio-Frequency Quadrupole

Design study of a beta=0.09 high current superconducting half wave resonator

Development and Measurements of A Technological Cavity for 350mhz High Current Proton Rfq

Tuning and Cold Test of A Four-Vane Rfq with Ramped Inter-Vane Voltage for the Compact Pulsed Hadron Source

RF Structure Design of a 201.5 MHz Deuteron RFQ Accelerator

Beam Dynamics Pre-Study For The Rfq Of Sppc P-Linac

CW/Pulsed H− Ion Beam Generation with PKU Cs-free 2.45 GHz Microwave Driven Ion Source

A 166.6 MHz Superconducting Rf System for the HEPS Storage Ring

Design of a 325MHz Beta=0.12 superconducting single spoke cavity for China-ADS