Abstract:The design progress of the Radio Frequency Quadrupole (RFQ) accelerator for the Compact Pulsed Hadron Source (CPHS) at Tsinghua University is presented in this paper. The RFQ will accelerate protons from 50 keV to 3 MeV, with the RF frequency of 325 MHz. The objective is to obtain the optimum structure of the RFQ accelerator with high transmission rate and tolerable total length. The beam dynamics are studied by the simulation of the proton beam in the RFQ accelerator with the code of PARMTEQM. The output proton beam from the RFQ is well matched into the DTL without Medium-Energy-Beam-Transport (MEBT) between the RFQ and DTL. INTRODUCTION A 325 MHz Radio Frequency Quadrupole (RFQ) accelerator will be built to produce 50mA of proton beam at 3 MeV as an injector of the 13 MeV DTL for the Compact Pulsed Hadron Source (CPHS) project at Tsinghua University. The CPHS project is a universitybased proton accelerator platform (13 MeV, 16 kW, peak current 50 mA, 0.5 ms pulse width at 50 Hz) for multidisciplinary neutron and proton applications [1]. The RFQ system consists of three four-vane resonant cavity sections, one power coupler, 47 slug tuners, 8 dipole-mode stabilizer rods, the RF power supply and its low-level control, vacuum, water cooling, resonance control, beam diagnostics, support and alignment systems. Fig. 1 shows the sketch of the RFQ system and the design parameters are listed in Table 1. Figure 1: Sketch of the 3 MeV RFQ for the CPHS project. To save space and cost, no Medium-Energy-BeamTransport (MEBT) will be placed between the RFQ and DTL. The RFQ is carefully designed to match the beam from the high-energy end of the RFQ to the entrance of the DTL, by reducing the focusing in the exit of the RFQ. The cavity cross section and vane-tip geometry are tailored as a function of longitudinal position. The physics design has been completed. One test section made by aluminium has been machined to verify the capability of the numerically controlled milling machine. The final RFQ cavity is now under construction. This paper summarizes the current physics and mechanical design of the CPHS RFQ and presents the fabrication status of the test section. Table 1: Design Parameters of the CPHS RFQ Parameters Value Unit

The pku terahertz facility at peking university *

Superconducting Accelerator-Based Pku-Thz Facility

Design of RFQ Accelerator Facility of PKUNIFTY

Initial Design Of High Power Coherent Terahertz(Thz) Source

Radio-Frequency Power Test of A Four-Rod Rfq Accelerator for Pkunifty

Research on Peking University Superconducting Accelerator Facility (PKU-SCAF)

Peking university superconducting accelerator facility for free electron laser

Design of a High Average Power Terahertz-Fel Facility

Design of RF Power System for CPHS

Neutronic design and simulated performance of Peking University Neutron Imaging Facility (PKUNIFTY)

A 3-Mev RFQ Accelerator for the Compact Pulsed Hadron Source at Tsinghua University

Design and Optimization of IR SASE FEL at Peking University**Work Supported by Chinese Department of Science and Technology under the National Basic Research Projects No. 2002CB713600.

Construction status of the CPHS RFQ at Tsinghua University

Super-radiation Terahertz Source Based on Sub-picosecond Electron Beam at CTFEL

Development of Tsinghua X-Band High Power Test Facility

Pkunifty: A Neutron Imaging Facility Based on an Rfq Accelerator

Design of the CPHS RFQ Linac at Tsinghua University

RF power system for compact pulsed hadron source

Commissioning and Operation of the Deuteron Injector for Pkunifty Project

Development of the 3MeV RFQ for the compact pulsed hadron source at tsinghua university

Study on the planar undulator scheme with focusing properties for pku-fel *