Abstract:A new selective catalytic reduction (SCR) system for captive power plants in the petrochemical industry was analyzed. The key components suitable for the target SCR system were obtained using computational fluid dynamics (CFD) numerical simulation combined with a cold physical model. The structural characteristics of the SCR system were studied, and corresponding design schemes were obtained for the key components, such as the guide plate, the ammonia injection grid (AIG), the static mixer, and the rectifier grille. The distributions of the flue gas velocity and the NH3 concentration within the flue cross-section in front of the first layer catalyst were studied in detail. Synchronously, the pressure loss and the temperature reduction characteristics in the SCR system were also considered. CFD results showed that the average standard deviation of the flue gas velocity was about 11.61%, and the average standard deviation of the NH3 concentration distribution could reach about 3.79% under the five operating conditions. It could be concluded that the uniformity of the flue gas velocity and the NH3 concentration distribution within the above flue cross-section was guaranteed by comparing to the design standard of 15% and 5%, respectively. It was further found that the maximum pressure loss between the inlet and the first layer catalyst was about 106.64 Pa, and the temperature reduction characteristic of the entire SCR system could be maintained within ±0.01 °C, which indicated that no extreme adverse effect arose due to the introduce of the key components. The cold physical model experiment was accordingly conducted to verify the reliability of the above CFD results. The cold physical model experiment results showed that the average standard deviation of flue gas velocity was about 8.82%, and the average standard deviation of NH3 concentration distribution could reach about 4.21%. The maximum biases for the standard deviations of the flue gas velocity and the NH3 concentration distribution were approximately 4.83% and 1.18% under the five operating conditions. Based on the good agreement of the research results via the two different methods, the designed key components of a new SCR system could be confirmed to be feasible, which would benefit the deNOx performance of the SCR system.

Influence of the Flue Gas Velocity Field at an Ammonia-injectian Grid on Uniform Flow and Reducing-gent Mixing Performance of a High-efficiency SCR (selective Catalytic Reduction) Device

Optimizing Flow Field in an SCR System of a 600 MW Power Plant: Effects of Static Mixer Alignment Style

Fluid Mixing Optimization Strategy of Catalytic Reactor for Marine SCR System

Optimization of Ammonia Injection Grid in Hybrid Selective Non-Catalyst Reduction and Selective Catalyst Reduction System to Achieve Ultra-Low NOx Emissions

Influence of Non-uniform Distributions of Inlet Velocity and Reductant on SCR DeNOx Performance

Integrated Gas and Solid Model to Determine the Flow Performance in the SCR Reactor

Coordinated Optimization Control of Flue Gas Temperature for Improving Reaction Efficiency of Catalyst

Investigating the Optimization Design of Internal Flow Fields Using a Selective Catalytic Reduction Device and Computational Fluid Dynamics

MODEL TEST AND NUMERICAL ANALYSIS OF FLOW FIELD IN SCR DENITRIFICATION SYSTEM IN SECOND-PHASE PROJECT OF SANHE POWER PLANT

STUDY ON FLOW FIELD OF THE SCR EQUIPMENT FOR A 300 MW UNIT BOILER

CFD analysis of influencing factors on SCR denitration efficiency of sintering flue gas based on response surface methodology

Mixing Performance of Preheated Flue Gas Entering Selective Catalytic Reactor under Low Loads

Change of Ammonia Escape Rate and SO3 Conversion Rate of SCR Denitration in Full Load Range

Design and Verification of Key Components of a New Selective Catalytic Reduction System in a Petrochemical Captive Power Plant

Experimental Investigation on the Mixing Performance of Heating Gas into the Low Temperature Sintering Flue Gas Selective Catalyst Reaction Facilities

Effect of Catalyst Inlet Flow Field Distribution Characteristics on Outlet NO Concentration Distribution in SCR Denitration Reactor Based on Monte Carlo Method

Study on Optimization Experiment of SCR Denitrification Technologies in a Coal-fired Power Plant

Evaluation system for testing performance of selective catalytic reduction (SCR) denitration catalyst

Research on Lean NO_x Removal by Plasma Enhanced Selective Catalytic Reduction over InZSM-5

Simulation of the flow field and the chemical reaction coupling of selective catalytic reduction (SCR) system using an orthogonal experiment

Numerical Simulation on Optimization of SCR Denitrification System for Coal-fired Boilers