Abstract:A new selective catalytic reduction (SCR) system for captive power plants in the petrochemical industry was analyzed. The key components suitable for the target SCR system were obtained using computational fluid dynamics (CFD) numerical simulation combined with a cold physical model. The structural characteristics of the SCR system were studied, and corresponding design schemes were obtained for the key components, such as the guide plate, the ammonia injection grid (AIG), the static mixer, and the rectifier grille. The distributions of the flue gas velocity and the NH3 concentration within the flue cross-section in front of the first layer catalyst were studied in detail. Synchronously, the pressure loss and the temperature reduction characteristics in the SCR system were also considered. CFD results showed that the average standard deviation of the flue gas velocity was about 11.61%, and the average standard deviation of the NH3 concentration distribution could reach about 3.79% under the five operating conditions. It could be concluded that the uniformity of the flue gas velocity and the NH3 concentration distribution within the above flue cross-section was guaranteed by comparing to the design standard of 15% and 5%, respectively. It was further found that the maximum pressure loss between the inlet and the first layer catalyst was about 106.64 Pa, and the temperature reduction characteristic of the entire SCR system could be maintained within ±0.01 °C, which indicated that no extreme adverse effect arose due to the introduce of the key components. The cold physical model experiment was accordingly conducted to verify the reliability of the above CFD results. The cold physical model experiment results showed that the average standard deviation of flue gas velocity was about 8.82%, and the average standard deviation of NH3 concentration distribution could reach about 4.21%. The maximum biases for the standard deviations of the flue gas velocity and the NH3 concentration distribution were approximately 4.83% and 1.18% under the five operating conditions. Based on the good agreement of the research results via the two different methods, the designed key components of a new SCR system could be confirmed to be feasible, which would benefit the deNOx performance of the SCR system.

Integrated Gas and Solid Model to Determine the Flow Performance in the SCR Reactor

Optimizing Flow Field in an SCR System of a 600 MW Power Plant: Effects of Static Mixer Alignment Style

Investigation On The Ash Deposition Of A Radiant Syngas Cooler Using Critical Velocity Model

Model Predictive Control Case Study: Selective Catalytic Reduction (scr) System in Coal-Fired Power Plant

Investigating the Optimization Design of Internal Flow Fields Using a Selective Catalytic Reduction Device and Computational Fluid Dynamics

MODEL TEST AND NUMERICAL ANALYSIS OF FLOW FIELD IN SCR DENITRIFICATION SYSTEM IN SECOND-PHASE PROJECT OF SANHE POWER PLANT

Design and Verification of Key Components of a New Selective Catalytic Reduction System in a Petrochemical Captive Power Plant

CFD analysis of influencing factors on SCR denitration efficiency of sintering flue gas based on response surface methodology

Dynamic evaluation of ash deposition behavior and parametric study using an inverse distance weighted interpolation dynamic mesh method

Quasi 1D Modeling of Two-Phase Flow and Deposit Formation for Urea-Selective Catalytic Reduction Systems

3D Modeling of Flow, Spray of Reductant and Surface Chemical Reaction in Diesel Urea SCR-NOx Catalytic Converter

Particle Conditioning for Improving Blockage Resistance of Denitration Catalysts in Sintering Flue Gas

STUDY ON FLOW FIELD OF THE SCR EQUIPMENT FOR A 300 MW UNIT BOILER

Dynamic CFD modeling and evaluation of ash deposition behaviors during Zhundong coal combustion

SIMULATION STUDY ON DESIGN OF INLET FLUE DUCT FOR SCR DENITRIFI CATION SYSTEM

Mechanisms and strategies for ash deposition reduction in flue gas heat exchanger

De-NOx Performance of Modified Fly Ash Supporting SCR Catalyst Under Various Molding Techniques

Large eddy simulation of hydrodynamics and deNOx process in a coal-fired power plant SCR system

CFD Modeling of Unsteady SCR Denox Coupled with Regenerative Heat Transfer in Honeycomb Regenerators Partly Coated by Vanadium Catalysts

Integrated Modeling of Semi-dry Flue Gas Desulfurization

CFD modelling of biomass ash deposition under multiple operation conditions using a 2D mass-conserving dynamic mesh approach