Abstract:A new selective catalytic reduction (SCR) system for captive power plants in the petrochemical industry was analyzed. The key components suitable for the target SCR system were obtained using computational fluid dynamics (CFD) numerical simulation combined with a cold physical model. The structural characteristics of the SCR system were studied, and corresponding design schemes were obtained for the key components, such as the guide plate, the ammonia injection grid (AIG), the static mixer, and the rectifier grille. The distributions of the flue gas velocity and the NH3 concentration within the flue cross-section in front of the first layer catalyst were studied in detail. Synchronously, the pressure loss and the temperature reduction characteristics in the SCR system were also considered. CFD results showed that the average standard deviation of the flue gas velocity was about 11.61%, and the average standard deviation of the NH3 concentration distribution could reach about 3.79% under the five operating conditions. It could be concluded that the uniformity of the flue gas velocity and the NH3 concentration distribution within the above flue cross-section was guaranteed by comparing to the design standard of 15% and 5%, respectively. It was further found that the maximum pressure loss between the inlet and the first layer catalyst was about 106.64 Pa, and the temperature reduction characteristic of the entire SCR system could be maintained within ±0.01 °C, which indicated that no extreme adverse effect arose due to the introduce of the key components. The cold physical model experiment was accordingly conducted to verify the reliability of the above CFD results. The cold physical model experiment results showed that the average standard deviation of flue gas velocity was about 8.82%, and the average standard deviation of NH3 concentration distribution could reach about 4.21%. The maximum biases for the standard deviations of the flue gas velocity and the NH3 concentration distribution were approximately 4.83% and 1.18% under the five operating conditions. Based on the good agreement of the research results via the two different methods, the designed key components of a new SCR system could be confirmed to be feasible, which would benefit the deNOx performance of the SCR system.

Model Predictive Control Case Study: Selective Catalytic Reduction (scr) System in Coal-Fired Power Plant

Optimizing Flow Field in an SCR System of a 600 MW Power Plant: Effects of Static Mixer Alignment Style

Closed-Loop Control Strategy and State Estimator for Diesel Engine SCR After-Treatment System

A Power Plant Coordinated Control System Using MPC

Get the design right, the rest is automatic: Towards an adaptive MPC controller

Model Predictive Control: A Unified Approach for Urea-Based SCR Systems

Multi‐model predictive control of SCR flue gas denitrification system in coal‐fired power plant based on kernel fuzzy c‐means clustering and integrated model

Development and verification of model predictive control strategy for selective catalytic reduction with rapid prototyping

Prediction and Control of the Nitrogen Oxides Emission for Environmental Protection Goal Based on Data-Driven Model in the SCR De-Nox System

Enhancement of SCR denitrification control strategy considering fluegas temperature fluctuation: Fundamental principle and performance evaluation

Multipollutant Control (MPC) of Flue Gas from Stationary Sources Using SCR Technology: A Critical Review

Design and Verification of Key Components of a New Selective Catalytic Reduction System in a Petrochemical Captive Power Plant

Real-time nonlinear model predictive control for optimizing the ammonia coverage ratio of an SCR system based on TC-QPSO

Application of an Improved State Feedback Control in the Selective Catalytic Reduction Denitrification Systems of Coal Power Units Under Variable Load Conditions

Model-Based Estimation and Control System Development in a Urea-SCR Aftertreatment System

Two-timescale Nonlinear Model Predictive Control for Flexible Operation of Coal-Fired Power Plant with Post Combustion CO2 2 Capture System

Adaptive Internal Model Control of SCR Denitration System Based on Multi-Objective Optimization

Nonlinear model predictive control applied to multivariable thermal and chemical control of selective catalytic reduction aftertreatment

Anticipatory NH3 injection control for SCR system based on the prediction of the inlet NOx concentration

Model-based NH3 Adaptation Method for SCR Control

Predictive control of SCR denitrification system in thermal power plants based on GA‐BP and PSO