Abstract:A new selective catalytic reduction (SCR) system for captive power plants in the petrochemical industry was analyzed. The key components suitable for the target SCR system were obtained using computational fluid dynamics (CFD) numerical simulation combined with a cold physical model. The structural characteristics of the SCR system were studied, and corresponding design schemes were obtained for the key components, such as the guide plate, the ammonia injection grid (AIG), the static mixer, and the rectifier grille. The distributions of the flue gas velocity and the NH3 concentration within the flue cross-section in front of the first layer catalyst were studied in detail. Synchronously, the pressure loss and the temperature reduction characteristics in the SCR system were also considered. CFD results showed that the average standard deviation of the flue gas velocity was about 11.61%, and the average standard deviation of the NH3 concentration distribution could reach about 3.79% under the five operating conditions. It could be concluded that the uniformity of the flue gas velocity and the NH3 concentration distribution within the above flue cross-section was guaranteed by comparing to the design standard of 15% and 5%, respectively. It was further found that the maximum pressure loss between the inlet and the first layer catalyst was about 106.64 Pa, and the temperature reduction characteristic of the entire SCR system could be maintained within ±0.01 °C, which indicated that no extreme adverse effect arose due to the introduce of the key components. The cold physical model experiment was accordingly conducted to verify the reliability of the above CFD results. The cold physical model experiment results showed that the average standard deviation of flue gas velocity was about 8.82%, and the average standard deviation of NH3 concentration distribution could reach about 4.21%. The maximum biases for the standard deviations of the flue gas velocity and the NH3 concentration distribution were approximately 4.83% and 1.18% under the five operating conditions. Based on the good agreement of the research results via the two different methods, the designed key components of a new SCR system could be confirmed to be feasible, which would benefit the deNOx performance of the SCR system.

CFD Modeling of Unsteady SCR Denox Coupled with Regenerative Heat Transfer in Honeycomb Regenerators Partly Coated by Vanadium Catalysts

Modeling, Simulation and Optimization of Commercial Naphtha Catalytic Reforming Process

Effects Of Promoters And Active Components On Performance Of Honeycomb Scr De-Nox Catalysts

Integrated Gas and Solid Model to Determine the Flow Performance in the SCR Reactor

Numerical Simulation of Selective Catalytic Reduction of NO and SO2 Oxidation in Monolith Catalyst

Large eddy simulation of hydrodynamics and deNOx process in a coal-fired power plant SCR system

CFD analysis of influencing factors on SCR denitration efficiency of sintering flue gas based on response surface methodology

3D Modeling of Flow, Spray of Reductant and Surface Chemical Reaction in Diesel Urea SCR-NOx Catalytic Converter

Modeling and Performance Analysis of SCR DeNOx Catalyst for Reducing NOx Emissions in Diesel Engine

Experimental and Numerical Simulation of Catalyst Deactivation Caused by Transient Turbulence in Gradient Flow Field

A Simulation Study of Heat and Mass Transfer in A Honeycombed Rotary Desiccant Dehumidifier

Design and Verification of Key Components of a New Selective Catalytic Reduction System in a Petrochemical Captive Power Plant

Optimization Analysis of Various Parameters Based on Response Surface Methodology for Enhancing NOx Catalytic Reduction Performance of Urea Selective Catalytic Reduction on Cu-ZSM-13 Catalyst

Modeling and Numerical Investigations of Flowing N-Decane Partial Catalytic Steam Reforming at Supercritical Pressure

CFD–DEM Simulation of Gas–solid Reacting Flows in Fluid Catalytic Cracking (FCC) Process

Effect of Catalyst Inlet Flow Field Distribution Characteristics on Outlet NO Concentration Distribution in SCR Denitration Reactor Based on Monte Carlo Method

Hydrothermal Aging Mechanism and Modeling for SCR Catalysts

Simulation of the flow field and the chemical reaction coupling of selective catalytic reduction (SCR) system using an orthogonal experiment

CFD-DEM Simulation of Gas-Solid Reacting Flows in Catalytic Reactor

Coupling ReaxFF molecular dynamics with computational fluid dynamics on the enhanced heat sink of n-decane decomposition initiated by nitroethane in the regenerative cooling channels

Investigating the Optimization Design of Internal Flow Fields Using a Selective Catalytic Reduction Device and Computational Fluid Dynamics