Abstract:When metals and alloys are subjected to considerable plastic deformation such as cold- or warm-rolling, characteristic inhomogeneities generally appeal as a form of deformation or shear bands. Recently much attention has been given to the deformation mechanism and morphology of fcc and bee materials. It is well known that such inhomogeneities play an essential role in the process of work-hardening, recrystallization, metal fatigue and fracture. Therefore, in order to obtain the guiding principle for controlling those processes in Mg based alloys, it; is in to make clear the details of those inhomogeneous deformation structures in hcp materials. In this work, the inhomogeneous deformation and microscopic features of AZ31 Mg based alloy were studied under compression at temperature ranging from 250 to 400 degrees C and at a strain rate of 3x10(-3) s(-1). The analysis of experimental data shows that such inhomogeneities depend on deformation temperature and strain sensitively. At 250 degrees C, the {10 (1) over bar2} c-axis extension twins and deformation bands appear at; around 45 degrees with the compression axis in grain interior when straining to epsilon=0.1, the {10 (1) over bar2} twins continue to grow until they impinge each other and finally most of the original grains are replaced by twinned grains at; a strain of about epsilon=0.2. The boundaries between {11 (1) over bar2} twins and their neighbors disappear during twinning. At 300 degrees C, in contrast, the non-basal slips are activated, the kink bands with low misorientation angles are frequently evolved in grain interior and they are roughly perpendicular to the (0001) basal plane, further deformation leads to an increase in the number and misorientation angle of the kink bands. The initial grains are fragmented by kinking. With temperature increasing, the spacing of kink bands increase rapidly. The difference between kinking and other deformation bands was discussed in some detail.

Twinning and Twin Intersection in Az31 Mg Alloy During Warm Deformation

Study of Twin Behavior During Uniaxial Compression of Az31 Magnesium Alloy

Twinning of AZ31 Magnesium Alloy Analyzed by EBSD Technique

Twinning Behavior in a Rolled Mg-Al-Zn Alloy under Dynamic Impact Loading

A Study of {10-12} Twinning Activity Associated with Stress State in Mg-3Al-1Zn Alloy during Compression

Study on twinning behaviors during multi-directional compression for AZ31 magnesium alloy by EBSD

Influence of Local Strain on Twinning Behavior During Compression of AZ31 Magnesium Alloy

Deformation Behaviour of Hot Extruded Mg Alloy Az31 During Compressive Deformation

The Dislocation-Twin Interaction and Evolution of Twin Boundary in AZ31 Mg Alloy

Influence of Grain Orientation on Twinning During Warm Compression of Wrought Mg–3Al–1Zn

Twinning Effects on the Hot Deformation Behavior of AZ31 Mg Alloy

EBSD Analysis and Theoretical Prediction of Twin Orientations During Compression in Mg-3Al-1Zn

Twin recrystallization mechanisms in a high strain rate compressed Mg-Zn alloy

Effect of Original Orientation on Microtexture Evolution of Az31 Mg Alloy

Microstructure Characterization of Twinning Under Impact Loading for AZ31B Magnesium Alloys

Effect of Pre-Strain on Extension Twinning Behavior in an Extruded AZ31 Mg Alloy Observed by In-Situ EBSD

The Effect of Twin–twin Interaction in Mg 3al 1zn Alloy During Compression

Nucleation and Growth Analysis of {101‾2} Extension Twins in AZ31 Magnesium Alloy During In-Situ Tension

Quasi-in Situ Observation of Extension Twinning of AZ31 Magnesium Alloy under Co-Directional Dynamic Compression

MORPHOLOGY AND CRYSTALLOGRAPHIC CHARAC-TERISTICS OF DEFORMATION BANDS IN Mg ALLOY UNDER HOT DEFORMATION

Role of {101‾2} Twinning in the Anisotropy and Asymmetry of AZ31 Magnesium Alloy under High Strain Rate Deformation