Abstract:In this study, the twinning–detwinning behavior and slip behavior of rolled AZ31 magnesium-alloy plates during a three-step intermittent dynamic compression process along the rolling direction (RD) and normal direction (ND), are investigated via quasi-in situ electron backscatter diffraction, and the causes of the twinning and detwinning behavior are explained according to Schmid law, local strain coordination, and slip trajectories. It is found that the twins are first nucleated and grow at a compressive strain of 3% along the RD. In addition to the Schmid factor (SF), the strain coordination factor (m') also influences the selection of the twin variants during the twinning process, resulting in the nucleation of twins with a low SF. During the second and third steps of the application of continuous compressive strains with magnitudes and directions of 3%RD+3%ND and 3%RD+3%ND+2.5%ND, detwinning occurs to different extents. The observation of the detwinning behavior reveals that the order in which multiple twins within the same grain undergo complete detwinning is related to Schmid law and the strain concentration, with a low SF and a high strain concentration promoting complete detwinning. The interaction between slip dislocations and twin boundaries in the deformed grains as well as the pinning of dislocations at the tips of the {101¯2} tensile twins with a special structure result in incomplete detwinning. Understanding the microstructural evolution and twinning behavior of magnesium alloys under different deformation geometries is important for the development of high-strength and high-toughness magnesium alloys.

EBSD Analysis and Theoretical Prediction of Twin Orientations During Compression in Mg-3Al-1Zn

Identification and Analysis of Twinning Variants During Compression of a Mg–Al–Zn Alloy

Influence of Grain Orientation on Twinning During Warm Compression of Wrought Mg–3Al–1Zn

A Study of {10-12} Twinning Activity Associated with Stress State in Mg-3Al-1Zn Alloy during Compression

Study of Twin Behavior During Uniaxial Compression of Az31 Magnesium Alloy

Twinning Behavior, Microstructure Evolution and Mechanical Property of Random-Orientated ZK60 Mg Alloy Compressed at Room Temperature

Atomic Motion in Mg–3Al–1Zn During Twinning Deformation

Influence of Local Strain on Twinning Behavior During Compression of AZ31 Magnesium Alloy

Twinning of AZ31 Magnesium Alloy Analyzed by EBSD Technique

Twinning Behavior in a Rolled Mg-Al-Zn Alloy under Dynamic Impact Loading

Quasi-in Situ Electron Backscatter Diffraction Analysis of Twinning–detwinning Behavior in AZ31 Magnesium- Alloy Rolled Plates Subjected to Compression Loading in Different Directions

Observation and Analysis of the Coexistence of Two “opposite” Twin Modes in a Mg-Al-Zn Alloy

Quantitative investigation on the {10–12} twinning-detwinning behavior and twinning transfer of an extruded Mg-2.8Y sheet during compression-tension loading via quasi-in-situ EBSD observation

The Effect of Twin–twin Interaction in Mg 3al 1zn Alloy During Compression

In Situ Characterization of Deformation Twinning in Magnesium During Cyclic Loading Via Electron Backscatter Diffraction

Influence of observation plane on twin variant identification in magnesium via trace and misorientation analysis

Twin recrystallization mechanisms in a high strain rate compressed Mg-Zn alloy

Twinning and Mechanical Behavior of an Extruded Mg–6Al–3Sn Alloy with a Dual Basal Texture

Influence of Twinning-Induced Recrystallization on Texture Evolution in a High Strain Rate Compressed Mg-Zn Alloy

Comparative Examinations on the Activity and Variant Selection of Twinning During Tension and Compression of Magnesium Alloys

Reducing the Tension–compression Yield Asymmetry in a Hot-Rolled Mg–3Al–1Zn Alloy Via Multidirectional Pre-Compression