Abstract:In this study, shear rheological polishing was used to polish the Si surface of six-inch 4H-SiC wafers to improve polishing efficiency. The surface roughness of the Si surface was the main evaluation index, and the material removal rate was the secondary evaluation index. An experiment was designed using the Taguchi method to analyze the effects of four critical parameters (abrasive particle size, abrasive particle concentration, polishing speed, and polishing pressure) on the Si surface polishing of SiC wafers. By evaluating the experimental results for the signal-to-noise ratio, the weight of each factor was calculated using the analysis of variance method. The optimal combination of the process parameters was obtained. Below are the weightings for the influence of each process on the polishing result. A higher value for the percentage means that the process has a greater influence on the polishing result. The wear particle size (85.98%) had the most significant influence on the surface roughness, followed by the polishing pressure (9.45%) and abrasive concentration (3.25%). The polishing speed had the least significant effect on the surface roughness (1.32%). Polishing was conducted under optimized process conditions of a 1.5 μm abrasive particle size, 3% abrasive particle concentration, 80 r/min polishing speed, and 20 kg polishing pressure. After polishing for 60 min, the surface roughness, Ra, decreased from 114.8 to 0.9 nm, with a change rate of 99.2%. After further polishing for 60 min, an ultrasmooth surface with an Ra of 0.5 nm and MRR of 20.83 nm/min was obtained. Machining the Si surface of 4H-SiC wafers under optimal polishing conditions can effectively remove scratches on the Si surface of 4H-SiC wafers and improve the surface quality.

Research on Polishing End Face of Silica Optical Fiber

The Deterioration Characteristics and Mechanism of Polishing Pads in Chemical Mechanical Polishing of Fused Silica

Achieving Ultralow Surface Roughness and High Material Removal Rate in Fused Silica Via a Novel Acid SiO2 Slurry and Its Chemical-Mechanical Polishing Mechanism

Application of surface analysis in study on removal mechanism and abrasive selection during fused silica chemical mechanical polishing

Investigation on Electrical Enhanced Photocatalysis Polishing of Single-Crystal Silicon Carbide Substrates

Investigation of the Chemical Residuals on the Fused Silica During Chemical Mechanical Polishing

High efficiency polishing of silicon carbide by applying reactive non-aqueous fluids to fixed abrasive pads

Characteristics of Slurry Recycling in Chemical Mechanical Polishing (CMP) of Fused Silica (FS)

Research on Polishing Performances and Mechanisms of CeO2/SiO2 Composite Abrasives

Towards Investigating Surface Quality of Single-Crystal Silicon Optics Polished with Different Processes

A High-Precision D-Shaped Fiber Polishing Method and its Sensing Characteristics of Different Polishing Depths

XPS, UV–vis Spectroscopy and AFM Studies on Removal Mechanisms of Si-face SiC Wafer Chemical Mechanical Polishing (CMP)

Polystyrene-Silica Composite Particles and Their Copper Chemical Mechanical Polishing Performances

Single crystal silicon wafer polishing by pretreating pad adsorbing SiO2 grains and abrasive-free slurries

Influence of surface morphology and processing parameters on polishing of silicon carbide ceramics using femtosecond laser pulses

Experimental Study on Shear Rheological Polishing of Si Surface of 4H-SiC Wafer

Methods and Mechanistic Analysis of Improving the Dispersion of Nano Silica Colloidal Particles in Chemical Mechanical Polishing Slurries

Preparation of Silane Modified Sio2 Abrasive Particles and Their Chemical Mechanical Polishing (cmp) Performances

Study on Pitch Performance Deterioration in Chemical Mechanical Polishing of Fused Silica

Optimization of polishing fluid composition for single crystal silicon carbide by ultrasonic assisted chemical-mechanical polishing

Material removal mechanism of single crystal silicon by bonnet polishing