Abstract:High-textured pyrolytic carbon (PyC) is the ideal interface for SiC fiber-reinforced SiC matrix (SiCf/SiC) composites. To prepare high-textured PyC coatings on SiC fibers efficiently, chemical vapor deposition (CVD) technique was applied with the single precursor ethanol. The effects of CVD parameters on the morphology and textures of PyC were investigated in detail. Rough laminar (RL), smooth laminar (SL) and regenerative laminar (ReL) PyC could be obtained by controlling the CVD parameters. High-textured RL PyC could be stably synthesized in a large distance range in the horizontal tube furnace at 1150 °C and 10–20 kPa (total pressure), which inferred that low temperature and negative pressure were beneficial to the formation of RL PyC. Conversely, when the temperature was up to 1350 °C, the textures of PyC at different deposition positions varied considerably. In the vicinity of isothermal zone, the texture evolution of PyC with deposition positions followed the pattern of SL→RL→SL, which could be ascribed to the ratio change of the small linear hydrocarbons (fillers) and the aromatic hydrocarbons (particles) in the gas phase. The texture evolution followed the Particle-Filler model. In addition to PyC textures, the PyC coating thickness played a critical role in regulating the mechanical properties of SiC fibers and SiCf/SiC composites. In the present work, the effects of thickness of RL PyC coatings on the tensile properties of SiC fibers were investigated. The SiC fibers with 0.3 μm RL PyC coating showed the highest average tensile strength (2735 MPa) and Weilbull modulus (10.34), which might be ascribed to the repair of fiber surface defects and the appropriate stress state between fibers and coatings. The results could provide essential data for the interface design and optimization of SiCf/SiC composites.

Microstructure and flexural properties of C/SiC composites by CVI-RMI method

Mechanical Behavior of SiCf/SiC Composites with Alternating PyC/SiC Multilayer Interphases

Influence of SiC Coating Thickness on Mechanical Properties of SiCf/SiC Composite

Mechanical Properties of 3D KD-I SiCf/SiC Composites with Engineered Fibre–matrix Interfaces

Effect of chemical vapor infiltration on the flexural properties of C/C-SiC composites prepared by the precursor infiltration pyrolysis method

Fabrication of C/SiC composites by siliconizing carbon fiber reinforced nanoporous carbon matrix preforms and their properties

Microstructures and properties of C/C–SiC composites derived from different gaseous carbon matrix precursors

Microstructure and mechanical properties of SiC fiber/Si-CoSi2 matrix composites fabricated by carbon chemical vapor infiltration and Si alloy melt infiltration process

A novel porous carbon synthesized to serve in the preparation of highly dense and high-strength SiC/SiC by reactive melt infiltration

Effects of CVI SiC amount and deposition rates on properties of SiCf/SiC composites fabricated by hybrid chemical vapor infiltration (CVI) and precursor infiltration and pyrolysis (PIP) routes

PyC interphase growth mechanism and control models of C/SiC composites

Microstructure and properties of CNTs reinforced CVI-pyrocarbon matrix

Microstructure and mechanical properties of SiC f /SiC composite prepared by chemical vapor infiltration

Thermal conductivity and bending strength of SiC composites reinforced by pitch-based carbon fibers

Microstructure and flexural strength of C/HfC-ZrC-SiC composites prepared by reactive melt infiltration method

Microstructure and mechanical properties of short-carbon-fiber/Ti3SiC2 composites

The Effect of PyC/SiC Compound Interphase on the Properties of PIP SiC/SiC Composite

Effects of preform structure on microstructure and mechanical properties of long/short fiber‐coupled C/C–SiC composites

Effect of pyrolytic carbon interphase on mechanical properties of mini T800-C/SiC composites

Mechanical properties and strengthening mechanism of SiCf/SiC mini-composites modified by SiC nanowires

Texture control of pyrolytic carbon coatings and effects of coating thickness on the tensile properties of SiC fibers