Abstract:Nickel-based superalloy IN713C produced through investment casting route is widely used for turbocharger turbine wheels in the automotive industry. The produced microstructure and microtexture are not homogeneous across the turbine component due to geometrical factors and localised cooling rate during the casting process, which give rise to inhomogeneous deformation during service. In the present paper, two kinds of in-house fatigue tests, Low Cycle Fatigue (LCF) and High Cycle Fatigue (HCF), were conducted at 600 °C in attempt to simulate the actual fatigue conditions experienced by turbine wheels in turbocharger. From Geometrically Necessary Dislocation (GND) distributions and strain analyses, it is concluded that microstructure heterogeneity such as carbide precipitates distribution within dendritic structure network determine the failure micromechanics during LCF tests. In the early stage of LCF loading, crack principally initiated within near surface carbides that have been oxidised during high temperature exposure. The higher GND density at the tip of carbide precipitates due to oxidation volume expansion are found to facilitate easy cracks initiation and propagation. Moreover, the cluster-like carbides network and its distribution can accelerate oxidation process and crack growth effectively. Furthermore, in the later stage of crack propagation during LCF, the weak interdendrite areas rotate to accommodate increased strain leading to faster cracks propagation and hence final catastrophic failure. Serial section technique for 3-D visualisation was employed to investigate the crystallographic grain orientation correlation with fracture mechanics during HCF loading. It appears that the microtexure and grain orientations are more critical than the alloy microstructure in an area with a relatively uniform carbides distribution and weak dendrite structure where HCF failure occurred. Based on the slip trace analysis, it was found that most faceting occurred in Goss grains (<110>//LD) and on slip system with the highest Schmid factor. It is concluded that cracks were initiated on planes with high Schmid factors and assisted by the presence of porosity.

Effects of Surface Defects on Rolling Contact Fatigue in 10Cr4ni4mo4v

Experimental Study of the Effects of Surface Defects on Rolling Contact Fatigue Behavior

Enhanced surface properties and contact fatigue performance of Cr4Mo4V bearing steel subjected to ultrasonic surface rolling processingVerbesserte Oberflacheneigenschaften und Kontaktermudungsleistung von einem ultraschall-oberflachengewalzten Cr4Mo4V-Lagerstahl

Effects of Surface Defects on Rolling Contact Fatigue of M50 Steel with Consideration to Both the Transgranular and Intergranular Damage

Rolling contact fatigue failure mechanism of bearing steel on different surface roughness levels under heavy load

Comparative Study on Surface Contact Fatigue of Machine Tool Bearing Raceways with Different Rolling Elements: Two Failure Bearings Case Studies

Surface integrity and rolling contact fatigue behavior of 18CrNiMo7-6 steel subjected to ultrasonic surface rolling process

Surface rolling deformed severity-dependent fatigue mechanism of Ti-6Al-4V alloy

Bending Fatigue Behaviour and Fatigue Endurance Limit Prediction of 20Cr2Ni4A Gear Steel after the Ultrasonic Surface Rolling Process

Experimental and Numerical Studies on Fatigue Crack Propagation of Surface Cracks in Heat-Resistant Steel CrMoCoV Considering Closure Effect

Effect of Primary Carbides on Rolling Contact Fatigue Behaviors of M50 Bearing Steel

Effects of defects on fatigue behavior of TC17 titanium alloy for compressor blades: Crack initiation and modeling of fatigue strength

Fretting Fatigue Behavior and Damage Mechanism of Cast Al-Si-Cu-T6 Alloy Under Two Surface Roughness conditions

Fatigue and recrystallization evolution of carbide-free bainitic layer under high-stress rolling sliding contact

Improved fretting fatigue mechanism of surface-strengthened Ti-6Al-4V alloy induced by ultrasonic surface rolling process

Influence mechanism of grinding surface quality of 20CrMnTi steel on contact failure

Rolling contact fatigue behaviors of 25CrNi2MoV steel combined treated by discrete laser surface hardening and ultrasonic surface rolling

The Effects of Microstructure and Microtexture Generated During Solidification on Deformation Micromechanism in IN713C Nickel-Based Superalloy

Influence of microstructure and microdefects on long-term fatigue behavior of a Cr-Mo-V steel

Study on Surface Integrity and Fatigue Properties of TC4 Titanium Alloy by Surface Ultrasonic Rolling

BEHAVIOR OF SHORT FATIGUE CRACKS IN MEDIUM CARBON BAINITIC BACK-UP ROLL STEEL UNDER MILD TRACTIVE ROLLING CONTACT