Abstract:Unlike many other surface treatment techniques, such as shot peening (SP), low plasticity burnishing (LPB), ultrasonic surface rolling process (USRP), ultrasonic nanocrystal surface modification (UNSM), laser shock peening (LSP) is a non-contact process. This means that LSP achieves surface modification without direct physical contact, thereby eliminating the risk of media contamination and undesired wear on the peening equipment. As a surface hardening technology, LSP tends to produce a hardened layer with a high gradient of residual stress (RS) in the near-surface, significantly enhancing wear resistance. The well-known wear theories applied for numerical prediction, whether Archard model or dissipated frictional-energy model, contain a multiplier for contact pressure and relative slip amplitude p·ds or shear stress and relative slip amplitude q·ds , respectively. These multipliers are sensitive to the mechanical properties near the surface. Additionally, the wear profile is governed not only by the wear effect but also by the deformation of materials. Therefore, to accurately evaluate the wear performance for surface-hardened materials, the influence of RS is hard to be overlooked. In this work, the finite element method (FEM) is utilised to construct a 3D numerical model, which ignores and considers RS, for both as-received and LSP-treated samples. Two distinct RS distributions induced by different scanning strategies (one- and five-time), are introduced in the finite element (FE) model. The numerical simulation results are then compared with the experimental data to verify the accuracy of the fretting wear model built in this study. On this basis, the impact of different RS distributions on fretting wear characteristics, including wear profile and volume, is extensively investigated. The findings reveal that higher amplitude RS can reduce the degree of fretting wear to a greater extent, highlighting the beneficial role of RS in enhancing wear resistance. Furthermore, the numerical models incorporating RS demonstrate superior predictive accuracy compared to those that omit RS. This naturally underscores the importance of integrating RS in numerical simulations of LSP and other surface-hardened materials.

Rolling contact fatigue and damage characteristic of AISI 9310 steel with pre-laser shock peening treatment

Research on Wear Resistance of AISI 9310 Steel with Micro-Laser Shock Peening

Rolling contact fatigue behaviors of 25CrNi2MoV steel combined treated by discrete laser surface hardening and ultrasonic surface rolling

Bending Fatigue Behaviour and Fatigue Endurance Limit Prediction of 20Cr2Ni4A Gear Steel after the Ultrasonic Surface Rolling Process

Microstructures and rolling contact fatigue behaviors of 17Cr2Ni2MoVNb steel under combined ultrasonic surface rolling and shot peening

The effect of shot peening on the contact fatigue performance of C40 steel gears after laser surface melting

Effect of laser shock peening on fretting wear behaviour of AISI 304 stainless alloy

Effect of Laser Shock Peening on the Fatigue Life of 1Cr12Ni3Mo2VN Steel for Steam Turbine Blades

Effect of laser shock peening on high cycle fatigue properties of aluminized AISI 321 stainless steel

Effect of laser shock peening on the retention ability of surface roughness in forged Cr5 steel

Optimization of multiple laser shock peening on high-cycle fatigue performance of aluminized AISI 321 stainless steel

Laser shock peening induced mechanical properties enhancement of 50CrVA alloy

Fatigue crack initiation and growth of laser shock peened 2Cr13 martensitic stainless steel as a function of the coverage layer

Effect of Warm Laser Shock Peening on the Low-Cycle Fatigue Behavior of DD6 Nickel-Based Single-Crystal Superalloy

Microstructural evolution and mechanical behaviors of Al-Cu-Li alloy processed by laser shock peening

The effect of laser shock peening on the rotating bending fatigue resistance of S51740 stainless steel

Effects of laser shock peening on fatigue crack growth rate and fracture properties of AA2524 aluminum alloy

Improvement of Fatigue Life of GH3039 Superalloy by Laser Shock Peening

Experimental and Numerical Studies of Fatigue Behavior of Ti6Al4V Alloy Treated by Laser Shock Peening

Fatigue strength improvement in Ti-6Al-4V subjected to foreign object damage by combined treatment of laser shock peening and shot peening

Finite Element Analysis Simulation of the Effect of Induction Hardening on Rolling Contact Fatigue