Abstract:Low-cycle fatigue (LCF) behavior of nickel-based precipitation-strengthened superalloy GH4145/SQ was investigated systematically under fully reversed total strain amplitude control conditions at 538°C in laboratory air. It was shown that the alloy exhibited a pronounced initial fatigue hardening followed by continuous fatigue softening to failure at high strain amplitudes, while at low strain amplitudes the initial hardening was followed by a well-defined saturation stage. Microstructure observations using optical and transmission-electron microscopy revealed that slip band density increased with increasing total strain amplitudes and the size of the γ′precipitates tended to reduction due to repeated shearing by the dislocations with continuous cyclic straining. The above changes in microstructures during cycling were essentially responsible for the fatigue hardening–softening behavior of the alloy. Both optical and SEM micrographs indicated that at low strain amplitudes crack propagation was basically transgranular, while at high strain amplitudes crack propagation was essentially intergranular. Bilinear behavior with a change of slope at a plastic strain amplitude of about 0.2pct was observed in cyclic stress–strain (CSS), Coffin–Manson (C–M) and plastic strain energy–life plots. A change in the number of operating slip systems and the fracture modes with the strain amplitude employed was used to explain this two-slope characteristic. In both the companion specimens test (CST) and the incremental step test (IST) methods the alloy exhibited non-masing type behavior. It was suggested that, for the first approximation, the half-life plastic strain energy could be calculated directly according to the equation without reckoning in the non-masing behavior.

Effect of Warm Laser Shock Peening on the Low-Cycle Fatigue Behavior of DD6 Nickel-Based Single-Crystal Superalloy

Low cycle fatigue behavior of nickel-based superalloy GH4145/SQ at elevated temperature

Impact on Mechanical Properties and Microstructural Response of Nickel-Based Superalloy GH4169 Subjected to Warm Laser Shock Peening

Research on Finite Element Simulation and Recrystallization of Laser Shock Peened Nickel-Based Single-Crystal Superalloy

Influence of Strain Amplitude on Low-Cycle Fatigue Behaviors of a Fourth-Generation Ni-Based Single-Crystal Superalloy at 980 °C

The effect of laser shock peening on very high cycle fatigue properties of laser welded 2A60 aluminum alloy joints

Improvement of Fatigue Life of GH3039 Superalloy by Laser Shock Peening

Optimization of multiple laser shock peening on high-cycle fatigue performance of aluminized AISI 321 stainless steel

Experimental and Numerical Studies of Fatigue Behavior of Ti6Al4V Alloy Treated by Laser Shock Peening

Effect of Laser Shock Peening on High-Cycle Fatigue Performance of 1Cr18Ni9Ti/GH1140 Weld

Elevating Fatigue Life in Nickel-Based Superalloys Through Suppression of Persistent Slip Bands/markings Via High-Density Pulsed Electric Current Treatment

Effect of laser shock peening on high cycle fatigue properties of aluminized AISI 321 stainless steel

Multiscale Plasticity Behavior and Fatigue Performance of Laser Melting Multi-Layer Nickel-Based Superalloys Upon Heat Treatments

Fatigue performance improvement of laser shock peened hole on powder metallurgy Ni-based superalloy labyrinth disc

Improving high cycle fatigue performance of gas tungsten arc welded Ti6Al4V titanium alloy by warm laser shock peening

Effect of laser shock peening on the tensile behavior and notch sensitivity of Ni-based single-crystal superalloy

Microstructure and residual stress modulation of 7075 aluminum alloy for improving fatigue performance by laser shock peening

On the Microstructure, Residual Stress and Fatigue Performance of Laser Metal Deposited TC17 Alloy Subjected to Laser Shock Peening

Microstructural evolution and mechanical behaviors of Al-Cu-Li alloy processed by laser shock peening

Enhanced extra-long life fatigue resistance of a bimodal titanium alloy by laser shock peening

Comparison of surface integrity of GH4169 superalloy after high-energy, low-energy, and femtosecond laser shock peening