Abstract:Hypoeutectic Al–Si alloys are becoming increasingly popular in automotive and aerospace engineering fields due to their excellent overall performance, and grain refinement is regarded as an important way to improve casting and mechanical properties. Titanium (Ti) is a basic element for grain refinement; thus, a certain amount of Ti is often included in Al–Si alloys. In the present work, the changes in the grain refinement, mechanical, and casting properties of Al–Si alloys with different Ti concentration levels under various grain refinement conditions were systematically investigated. The specific roles of Ti in the heterogeneous nucleation of α-Al grains were summarized, and the formation mechanism of Ti-rich zones in Al–Si alloys was revealed. Excess Ti concentration could not efficiently reduce the grain size of Al–Si alloys and eventually resulted in inferior mechanical and casting qualities; hence, the recommended Ti concentration level for the aluminum alloy grades of A356 and A357 is ≤ 0.1 wt%. Furthermore, an optimized technique for the grain refinement of hypoeutectic Al–Si alloys was presented. A small amount of an Al–TCB master alloy was introduced to achieve the best grain refinement and mechanical properties in a trace Ti environment. The addition of 0.5 wt% of the Al–TCB master alloy at the Ti concentration level of 0.06 wt% increased the ultimate tensile strength, elongation, and quality index of the Al–7Si–0.45Mg alloy to 328.8 ± 5.0 MPa, 14.4 % ± 0.6 %, and 970.7 ± 33.1 MPa, respectively.

Effects of Refinement and Modification on Melt Structure of Hypoeutectic Al-Si Alloy

Study on the Apparent Viscosity and Microstructure of Semi-Solid Al-Si Alloy Prepared by Chemical Refining

The Circumstances and Development of Refinement and Modification of Hypoeutectic Al-Si Alloys

Study on the Effect of Pre-Refinement and Heat Treatment on the Microstructure and Properties of Hypoeutectic Al-Si-Mg Alloy

Modification mechanism and tensile property of Al-9Si-0.4Mg-0.1Cu alloy

Combined Treatment of Sr and B and Evaluation of Refinment-Modification Levels for Al-7si Casting Alloy

Constitutive relation between electric conductivity and microstructure characteristics parameters of hypoeutectic Al-Si alloys

Incubation and Fading of Sr Modification in Hypoeutectic Al-Si Alloys

Effect of Sr Modification on the Microstructures, Mechanical Properties, and Thermal Conductivity of Hypoeutectic Al-13.6Cu-6Si Alloys

Interactions of Melt Processes of Hypoeutectic Al-Si Alloys

Effect of Sr modification on microstructure and thermal conductivity of hypoeutectic Al−Si alloys

Thermodynamics of effect of modification on microstructure of Al-Si alloy melt

Effect of strontium and melt purification on the solidification microstructure of hypereutectic Al-Si alloys

Solidification microstructure manipulation mechanism of hypoeutectic and hypereutectic Al-Si alloys controlled by trace in-situ nano-Fe 2 B and nano-Fe 3 Si

The Effect of Solution Treatment on the Si Particles’ Morphology Evolution and the Thermal Conductivity and Tensile Properties of Sb-Modified Al-8Si-0.6Mg Alloys

Effect of ultrasonic melt processing and Al-Ti-B on the microstructural refinement of recycled Al alloys

Insights into the dual effects of Ti on the grain refinement and mechanical properties of hypoeutectic Al–Si alloys

Influence of Modification on Flow Stress Behavior and Corrosive Properties of a Hypoeutectic Al-Si Alloy

Microstructural refinement and tensile properties enhancement of Al-10Mg2Si cast alloys by copper addition

Microstructure control and performance evolution of hypereutectic Al–20Mg2Si alloy by novel Al–Ca–Sb master alloy

Factors affecting eutectic Si modification in Al-Si hypoeutectic alloy with the addition of Na, Sr, Eu and Yb