Abstract:The PP alloy was synthesized directly in the reactor with a 4(th) generation Ziegler-Natta catalyst. it is very different from mechanically blended PP alloys, its properties, especially its impact strength,are superior to those of the latter. However,so far the studies on the stucture of this kind of PP alloys have not been reported. The microstructure of a PP alloy was characterized by IR,DSC,and C-13-NMR. The sample was first fractionated and 8 fractions were obtained. The IR analysis showed that the ethylene content of each fraction is different. Except for the first fraction,which is an elastomer, the others are all hard powders at room temperature. Therefore, the fractions above 50 degreesC perhaps are all composed of ethylene-propylene block copolymers. DSC analysis showed that the melting curve of the PP alloy became broadened compared with that of i-PP,and a small peak appeared at 120 degreesC. The extracts of PP alloy in boiling heptane and every fractions of PP alloy all exhibited many small peaks. These peaks demonstrated that the macromolecular chains in PP alloy are composed of ethylene-propylene blocks,whose sequence length are very different. The C-13-NMR spectrum of fraction at 90 degreesC, similar to other fractions at 50 similar to 100 degreesC,also indicated that there are long ethylene sequences in macromolecualr chains of PP alloy. According to the above analysis,a conclusion was reached that the E-P copolymer in PP alloy is composed of EPR and E-P blocks,with different ethylene sequence length. This polydispersity structure in PP alloy made it possess very high impact property.

Progress on Research of Polypropylene Alloy Technology Within Reactor

Polypropylene and Ethylene−Propylene Copolymer Reactor Alloys Prepared by Metallocene/Ziegler−Natta Hybrid Catalyst

Regulation of Structure and Mechanical Properties of Poly(propylene-Butene) Alloys by Monomer Composition Switching

I-Pp/epr REACTOR ALLOY PREPARED THROUGH ETHYLENE/PROPYLENE SLURRY COPOLYMERIZATION CATALYZED BY METALLOCENE SUPPORTED Ipp PARTICLES

State-of-the-art and research progress of polyolefin-based elastomer

Preparation of Polypropylene/MMT Nanocomposites Using Complex Supported Catalysts

Polyolefin nanometer compound material and its preparation technology

Control of Diffusion/Barrier Effects of Polymer-Coated Particles and the Strengthening of Ethylene Polymerization Reactor

Advanced Catalyst Technology for Broad/Bimodal Polyethylene, Achieved by Polymer-Coated Particles Supporting Hybrid Catalyst

Enhanced Multiphase Interfacial Interaction of Impact Polypropylene Copolymer by In-Situ Introducing Polyethylene

Recent advances and prospect of ethylene terpolymerization

Synthesis of high toughness and stiffness polyolefin in-reactor alloys by reactor granule technology

Study of Polypropylene Reactor Alloying

Influence of Copolymerization Conditions on the Structure and Properties of Polyethylene/Polypropylene/Poly(Ethylene-Co-Propylene) In-Reactor Alloys Synthesized in Gas-Phase with Spherical Ziegler-Natta Catalyst

Improvement Of Structure And Properties Of Polypropylene/Poly(Ethylene-Co-Propylene) In-Reactor Alloy By Modifying The Cocatalyst

Structure and Morphology of Polyethylene/polypropylene In‐reactor Alloys Synthesized by Spherical High‐yield Ziegler–Natta Catalyst

Microstructure analysis of polypropylene reactor alloy

Regulating the Structure of Ethylene-Propylene Copolymer for Polyolefin In-Reactor Alloy with Improved Properties

Synthesis of high performance PE/PP/EPR in-reactor alloys by sequential multi-stage gas-phase polymerization with spherical Ziegler-natta catalyst

Synthesis of High Quality PE/PP In-Reactor Alloys with PE Matrix by Multi-Stage Polymerization

Characterization of Microstructure of Polypropylene Alloys