Abstract:The PP alloy was synthesized directly in the reactor with a 4(th) generation Ziegler-Natta catalyst. it is very different from mechanically blended PP alloys, its properties, especially its impact strength,are superior to those of the latter. However,so far the studies on the stucture of this kind of PP alloys have not been reported. The microstructure of a PP alloy was characterized by IR,DSC,and C-13-NMR. The sample was first fractionated and 8 fractions were obtained. The IR analysis showed that the ethylene content of each fraction is different. Except for the first fraction,which is an elastomer, the others are all hard powders at room temperature. Therefore, the fractions above 50 degreesC perhaps are all composed of ethylene-propylene block copolymers. DSC analysis showed that the melting curve of the PP alloy became broadened compared with that of i-PP,and a small peak appeared at 120 degreesC. The extracts of PP alloy in boiling heptane and every fractions of PP alloy all exhibited many small peaks. These peaks demonstrated that the macromolecular chains in PP alloy are composed of ethylene-propylene blocks,whose sequence length are very different. The C-13-NMR spectrum of fraction at 90 degreesC, similar to other fractions at 50 similar to 100 degreesC,also indicated that there are long ethylene sequences in macromolecualr chains of PP alloy. According to the above analysis,a conclusion was reached that the E-P copolymer in PP alloy is composed of EPR and E-P blocks,with different ethylene sequence length. This polydispersity structure in PP alloy made it possess very high impact property.

Study of Polypropylene Reactor Alloying

Regulation of Structure and Mechanical Properties of Poly(propylene-Butene) Alloys by Monomer Composition Switching

Polypropylene and Ethylene−Propylene Copolymer Reactor Alloys Prepared by Metallocene/Ziegler−Natta Hybrid Catalyst

I-Pp/epr REACTOR ALLOY PREPARED THROUGH ETHYLENE/PROPYLENE SLURRY COPOLYMERIZATION CATALYZED BY METALLOCENE SUPPORTED Ipp PARTICLES

Influence of Copolymerization Conditions on the Structure and Properties of Polyethylene/Polypropylene/Poly(Ethylene-Co-Propylene) In-Reactor Alloys Synthesized in Gas-Phase with Spherical Ziegler-Natta Catalyst

Microstructure analysis of polypropylene reactor alloy

Research on Toughening Modification of Copolymerized Polypropylene Using Polyolefin Elastomers

Characterization of Microstructure of Polypropylene Alloys

Influence of Polymerization Conditions on the Structure and Properties of Polyethylene/polypropylene In‐reactor Alloy Synthesized in the Gas Phase with a Spherical Ziegler–Natta Catalyst

Enhanced Multiphase Interfacial Interaction of Impact Polypropylene Copolymer by In-Situ Introducing Polyethylene

Regulating the Structure of Ethylene-Propylene Copolymer for Polyolefin In-Reactor Alloy with Improved Properties

Liquid Containing Particle Polymerization: Ethylene/-Olefin Reaction in a New Environment

On-line Fast Detection and Control of Composition for Binary Gas-Phase Copolymerization of Olefins

A Study on Olefin Polymer Alloy Based on Propylene

Control of Diffusion/Barrier Effects of Polymer-Coated Particles and the Strengthening of Ethylene Polymerization Reactor

Synthesis of Polypropylene/poly(ethylene-co-propylene) In-Reactor Alloys by Periodic Switching Polymerization Process: Dynamic Change of Gas-Phase Monomer Composition and Its Influences on Polymer Structure and Properties

STUDY ON THE SOLID PHASE STRUCTURE OF POLYPROPYLENE REACTOR BLENDS

Synthesis of High Quality PE/PP In-Reactor Alloys with PE Matrix by Multi-Stage Polymerization

Morphology and properties of PP in-reactor alloys prepared with a MgCl2/TiCl4/diisobutyl phthalate/phosphate tris-methylphenyl ester catalyst system

Effect of the Structure on the Morphology and Spherulitic Growth Kinetics of Polyolefin In‐reactor Alloys

Structure and Morphology of Polyethylene/polypropylene In‐reactor Alloys Synthesized by Spherical High‐yield Ziegler–Natta Catalyst