Abstract:The PP alloy was synthesized directly in the reactor with a 4(th) generation Ziegler-Natta catalyst. it is very different from mechanically blended PP alloys, its properties, especially its impact strength,are superior to those of the latter. However,so far the studies on the stucture of this kind of PP alloys have not been reported. The microstructure of a PP alloy was characterized by IR,DSC,and C-13-NMR. The sample was first fractionated and 8 fractions were obtained. The IR analysis showed that the ethylene content of each fraction is different. Except for the first fraction,which is an elastomer, the others are all hard powders at room temperature. Therefore, the fractions above 50 degreesC perhaps are all composed of ethylene-propylene block copolymers. DSC analysis showed that the melting curve of the PP alloy became broadened compared with that of i-PP,and a small peak appeared at 120 degreesC. The extracts of PP alloy in boiling heptane and every fractions of PP alloy all exhibited many small peaks. These peaks demonstrated that the macromolecular chains in PP alloy are composed of ethylene-propylene blocks,whose sequence length are very different. The C-13-NMR spectrum of fraction at 90 degreesC, similar to other fractions at 50 similar to 100 degreesC,also indicated that there are long ethylene sequences in macromolecualr chains of PP alloy. According to the above analysis,a conclusion was reached that the E-P copolymer in PP alloy is composed of EPR and E-P blocks,with different ethylene sequence length. This polydispersity structure in PP alloy made it possess very high impact property.

STUDY ON THE SOLID PHASE STRUCTURE OF POLYPROPYLENE REACTOR BLENDS

Regulation of Structure and Mechanical Properties of Poly(propylene-Butene) Alloys by Monomer Composition Switching

Studies on composition and molecular structure of high impact polypropylene

Microstructure analysis of polypropylene reactor alloy

Polypropylene and Ethylene−Propylene Copolymer Reactor Alloys Prepared by Metallocene/Ziegler−Natta Hybrid Catalyst

I-Pp/epr REACTOR ALLOY PREPARED THROUGH ETHYLENE/PROPYLENE SLURRY COPOLYMERIZATION CATALYZED BY METALLOCENE SUPPORTED Ipp PARTICLES

Enhanced Multiphase Interfacial Interaction of Impact Polypropylene Copolymer by In-Situ Introducing Polyethylene

Study of Polypropylene Reactor Alloying

A Study on Crystalline Structure and Morphology for Polypropylene Catalloys

Structure, morphology and non-isothermal crystallization behavior of polypropylene catalloys

Crystallization Behavior of the Blends of Isotactic Polypropylene and Ethylene-Propylene Blocky Copolymers

Crystalline Structure of Polypropylene Catalloys and Related Influence Factors

Characterization of Microstructure of Polypropylene Alloys

STUDY ON CRYSTALLIZATION BEHAVIOR OF ISOTACTIC POLYPROPYLENE PRODUCED BY SUPERCRITICAL POLYMERIZATION

Structure and morphology of polypropylene/poly(ethylene-co-propylene) in situ blends synthesized by spherical Ziegler–Natta catalyst

The influences of solid surface modification on the crystallizability of polypropylene

Effect of the Structure on the Morphology and Spherulitic Growth Kinetics of Polyolefin In‐reactor Alloys

Influence Of Cocatalyst On The Structure And Properties Of Polypropylene/Poly (Ethylene-Co-Propylene) In-Reactor Alloys Prepared By Mgcl2/Ticl4/Diester Type Ziegler-Natta Catalyst

EFFECT OF COMPOSITION ON CRYSTALLIZATION BEHAVIOR FOR POLYPROPYLENE CATALLOYS

Structure and properties of polypropylene/poly(ethylene-co-propylene) in-situ blends synthesized by spherical Ziegler–Natta catalyst

Structure and Morphology of Polyethylene/polypropylene In‐reactor Alloys Synthesized by Spherical High‐yield Ziegler–Natta Catalyst