Abstract:Al-SiCw composites can be readily shaped with conventional secondary metalworking techniques. During such forming operations, Al-SiCw composites may experience appreciable amounts of cold work, which may both influence their further forming operations and degrade some mechanical properties. Therefore, after forming operations it may be necessary to anneal the composites. Mostly, recrystallization annealing is used to achieve this purpose. The purpose of this study is to give useful information on thermomechanical processing of Al-SiCw composites by investigating their recrystallization kinetics. Al/SiC/15w composites are fabricated through a squeeze casting route followed by a hot extrusion at an extrusion ratio of 18: 1, and cold-rolled to 30, 50, and 70% of the original thickness, respectively. Then as-cold-rolled Al/SiC/15w composites are heated either continuously or isothermally to make the composites recrystallize. To investigate the kinetics of the cold-rolled composites during heating, differential thermal analysis (DTA) and hardness testing are carried out. It is found that the recrystallization kinetics of Al/SiC/15w composites is strongly dependent on deformation degree. When the reduction in thickness is less than 50%, with the increase in reduction in thickness, a faster kinetics of recovery and recrystallization occur. When the reduction in thickness is more than 50%, however, with the increase in reduction in thickness, only a faster kinetics of recovery occurs and the kinetics of recrystallization is nearly not influenced. Whiskers play a role in promoting the kinetics of recrystallization by particle-stimulated nucleation (PSN). While solute atoms make the kinetics of recrystallization largely delayed, precipitates only slightly slow down the recrystallization kinetics. At 280°C, between 100 and 200 s, extended recovery reaction and recrystallization nucleation are dominant. After 200 s, however, the growth of recrystallized grains becomes a dominant softening mechanism. As a result of the recrystallization taking place before aging, aging kinetics of the cold-rolled solution-treated 6061Al-SiCw composite is delayed.

Microstructural Evolution in Cold-Rolled Squeeze-Cast Sicw/Al Composites During Annealing

Rolling and Annealing Textures of SiCw/Al Composite

Rolling and annealing textures of a SiCw/Al composite

Recrystallization Kinetics of Cold-Rolled Squeeze-Cast Al/Sic/15w Composites

Effect of cold-rolling on tensile strength of SiCw/Al composite

Effect of Cold-Rolling on Hardness of SiCw/Al Composite

Forming process of hot-extruded SiCw/6061AI composites(I)

The Effect of Annealing Temperature on Micro-Structure and Mechanical Properties of C/Sic Composites

Effects of Hot Rolling on Microstructure and Properties of a 20 Vol.% SiC P /al Composite

Evolution of Microstructure, Texture and Mechanical Properties of SiC/AZ31 Nanocomposite During Hot Rolling Process

The Effects of Cold Rolling and Annealing on the Microstructure Evolution of Ordered C-2000 Alloy during Metallic Wire Preparation

Effect Of Hot-Deformation On Microstructure And Mechanical Properties Of (Sicw Center Dot Sicp)/2024al Hybrid Nanocomposites

Static Recrystallization Behavior and Texture Evolution during Annealing in a Cold Rolling Beta Titanium Alloy Sheet

X-RAY DIFFRACTION ANALYSIS FOR THE RECRYSTAL- LIZATION BEHAVIOR OF SiCw/Al COMPOSITE AT HIGH TEMPERATURE

Effect of hot rolling on microstructures and mechanical properties of SiC p /A356 aluminum matrix composites

Effect of annealing treatment on stress corrosion cracking behavior of SiC whisker reinforced aluminum composite

Effect of Hot Rolling on Microstructures and Mechanical Properties of SiCp/A356 Aluminum Matrix Composites

Evolutions of Microstructure and Crystallographic Texture in an Fe-1.2 wt.% Si Alloy After (A)Symmetric Warm Rolling and Annealing

Compressive Stress-Strain Response of Directionally Aligned Sicw/Al Composite

Microstructure Evolution of Sicw/Az91 Magnesium Matrix Composite During High Temperature Compression

The effect of whisker misalignment on the hot compressive deformation behavior of SiCw/6061 Al composites at 500°C