Abstract:Implementation of sodium metal anode is highly desired for sodium batteries due to its high theoretical capacity and low redox potential. Unfortunately, formation of unstable solid electrolyte interphase (SEI) and uncontrollable growth of dendrites during charge/discharge cycles greatly hinder the practical application of sodium metal anode. In this study, an organic-metal artificial layer made of PVdF and Bi was constructed to protect Cu current collector via a facile coating method, leading to smooth and dense sodium plating/stripping, which in retern enables stable cycling and high coulombic efficiency (CE). At 1 mA cm(-2), PB@Cu current collector presents extended lifetime of similar to 2500 h with high sodium utilization of 50%, which is approximately six times higher than Cu current collector. PB@Cu electrode also displays high average CE of 99.92% and 99.95% over 2500 and 1300 cycles at 1 and 2 mA cm(-2) respectively, which is in sharp contrast to the low and tremendously fluctuant CE gained from bare Cu electrode. Moreover, stable capacity of > 90 mAh g(-1) over 150 cycles is realized for PB@Cu-based full cell assembled with NVP cathode at a low negative-positive capacity ratio of similar to 3.5, which is significantly higher than 37.2 mAh g (-1) obtained from NVP/Cu at 150 th cycle. The superior electrochemical performance of PB@Cu current collector is revealed to originate from the alloyed Na3Bi phase with high sodium conductivity and robust mechanical strength as well as the formation of NaF-rich SEI with fast sodium ion migration, which enable dendrite-free morphology during plating/stripping cycles. (C) 2021 Published by ELSEVIER B.V. and Science Press on behalf of Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences.

Sodium Stearate, an Effective Amphiphilic Molecule Buffer Material Between Organic and Metal Layers in Organic Light-Emitting Devices

Photoemission Study of the Sodium Stearate/tris-(8-hydroxyquinoline) Aluminum Interface

Mechanisms of Injection Enhancement in Organic Light-Emitting Diodes Through Insulating Buffer

Enhancement of Electron Injection in Organic Light-Emitting Devices Using an Ag/LiF Cathode

Superior Stable and Long Life Sodium Metal Anodes Achieved by Atomic Layer Deposition.

Improved Performance of Organic Light-Emitting Diodes with MgF 2 As the Anode Buffer Layer

Improvement of Electron–hole Injection Balance in Si-anode Organic Light-Emitting Diodes by Using Enhanced Electron Injection Organic of Fluorinated Tris-(8-hydroxy-quinolinato) Aluminum

Organic light-emitting devices with a 2-(4-biphenyl)-5-(4-butylphenyl)-1,3,4-oxadiazole layer between the α-naphtylphenyliphenyl diamine and 8-hydroxyquinoline aluminum

Efficient light emitting diodes with Teflon buffer layer

Small-Molecule Organic Solar Cells with Improved Stability

Efficient Single-Active-Layer Organic Light-Emitting Diodes With Fluoropolymer Buffer Layers

Efficient Organic Light-Emitting Diode Using Lithium Tetra(8-Hydroxy-Quinolinato) Boron As the Electron Injection Layer

Stabilizing Sodium Metal Anode Through Facile Construction of Organic-Metal Interface

Li : Mg Alloy with Variable Work Function As Highly Efficient Cathode for Organic Light-Emitting Devices

Highly stable CsPbBr3 perovskite quantum dots incorporated in aluminum stearate

Air stability of Cs2CO3:Ag/Ag cathode for organic light-emitting diodes

Improving the Performance of Perovskite Solar Cells with Sodium Stearate-Doped PEDOT:PSS as a Hole Transport Layer

Effective Intermediate Layers for Highly Efficient Stacked Organic Light-Emitting Devices

Octylammonium Sulfate Decoration Enhancing the Moisture Durability of Quasi‐2D Perovskite Film for Light‐Emitting Diodes

Simultaneous Regulation of Organic and Inorganic Components in Interphase by Fiber Separator for High‐stable Sodium Metal Batteries

Stable Sodium Metal Anode Enabled by an Interface Protection Layer Rich in Organic Sulfide Salt