Abstract:Selective laser reaction sintering techniques (SLRS) techniques were investigated for the production of near net-shape non-oxide ceramics including SiC, Si3N4, and HfC/SiC composites that might be compatible with prevailing powder bed fusion additive manufacturing processes. Reaction bonded layers of covalent ceramics were produced using in-situ reactions that occur during selective laser processing and layer formation. During SLRS, precursor materials composed of metal and/or metal oxide powders were fashioned into powder beds for conversion to non-oxide ceramic layers. Laser-processing was used to initiate simultaneous chemical conversion and local interparticle bonding of precursor particles in 100 vol% CH4 or NH3 gases. Several factors related to the reaction synthesis process—precursor chemistry, gas-solid and gas-liquid synthesis mechanisms, precursor vapor pressures—were investigated in relation to resulting microstructures and non-oxide yields. Results indicated that the volumetric changes which occurred during in-situ conversion of single component precursors negatively impacted the surface layer microstructure. To circumvent the internal stresses and cracking that accompanied the conversion of Si or Hf (that expands upon conversion) or SiOx (that contracts during conversion), optimized ratios of the precursor constituents were used to produce near isovolumetric conversion to the product phase. Phase characterization indicated that precipitation of SiC from the Si/SiO2 melt formed continuous, crack-free, and dense layers of 93.7 wt% SiC that were approximately 35 µm thick, while sintered HfC/SiC composites (84.2 wt% yield) were produced from the laser-processing of Hf/SiO2 in CH4. By contrast, the SLRS of Si/SiOx precursor materials used to produce Si3N4 resulted in whisker formation and materials vaporization due to the high temperatures required for conversion. The results demonstrate that under appropriate processing conditions and precursor selection, the formation of near net-shape SiC and SiC composites might be achieved through single-step AM-compatible techniques.

Synthesis Of Sic-Si3n4 Composite Nanoparticles By Laser-Induced Chemical Deposition

Synthesis and Growth Mechanism of Single Crystal Β‐si3n4 Particles with a Quasi‐spherical Morphology

Synthesis and thermal stability of SiC-Si3N4 composite ultrafine particles by laser-induced gas-phase reaction

Sic Nanocrystals: High-Rate Deposition and Nano-Scale Control by Thermal Plasma

Phase-controlled Synthesis of Nickel Silicide Nanostructures

Studies of synthesizing the SiC nanometer powders by chemical vapor reaction

Influence of micron and nano SiCp on microstructure evolution and mechanical properties of laser metal deposition AlSi10Mg alloy

Synthesis and investigation of the physicochemical properties of polymorphic 3C–SiC

Fabrication of Si3n4/Sic Nanocomposites by Spark Plasma Sintering of Amorphous Sicn Powders Derived from A Polymeric Precursor

Microstructure, Surface Morphology, and Mechanical Properties of Nanocrystalline Tin/Amorphous Si3n4 Composite Films Synthesized by Ion Beam Assisted Deposition

Large-scale Synthesis of Monodisperse SiC Nanoparticles with Adjustable Size, Stoichiometric Ratio and Properties by Fluidized Bed Chemical Vapor Deposition

Densification and Enhancement of Sic Particulate Reinforced Fine Grain Sic Ceramic

Synthesis of Silicon Nitride/Silicon Carbide Nanocomposite Powders through Partial Reduction of Silicon Nitride by Pyrolyzed Carbon

Deposition Of Nanocrystalline Cubic Silicon Carbide Films Using The Hot-Filament Chemical-Vapor-Deposition Method

Carbothermally prepared nanophase SiC/ Si3N4 composite powders and densified parts

Manipulation Of Phase And Microstructure At Nanoscale For Sic In Molten Salt Synthesis

Selective laser reaction synthesis of SiC, Si3N4 and HfC/SiC composites for additive manufacturing

Fabrication of 4H–SiC nanoparticles using femtosecond pulsed laser ablation in deionized water

Enhancing mechanical properties of selectively laser sintered SiC/Si composites printed using electrostatic spraying microspheres with fine particles

In‐situ combustion synthesis of spherical Si@Si3N4 granules

Investigation of ablation efficiency and properties of silicon carbide nanoparticles synthesised using pulsed laser ablation in liquid