Abstract:Micro-electro-mechanical system (MEMS) is a newly rising interdisciplinary, technology. The mechanical design of MEMS is one of the frontiers of mechanical engineering. The increasing use of small micro-electro-mechanical system (MEMS) and advanced sensors has lead to concern about the failure modes and reliability of these structures. This depends on the solution of materials issues associated with the design and fabrication of complex MEMS devices. The reliable mechanical properties of these thin films are critical to the safety and functioning of these microdevices and should be accurately determined. This paper takes up the key point among the existing problems in the development of MEMS, the mechanical behavior of MEMS materials, for investigating experimentally in detail. To investigate the specimen size influence on fracture strength of microstructures, the validity of a novel, direct and convenient method for bending strength measurements by beam bending using a nanoindenter has been demonstrated. The tensile strength of polysilicon thin films was measured with a microtensile test device with a magnet solenoid actuator and a fibre optical displacement sensor. The bending strength of microfabricated polysilicon beams with dimensions of 16 ∼ 34 μm long, 10 ∼ 50 μm wide, and 2.4 μm thick was evaluated. The tensile mechanical properties of microfabricated polysilicon thin films with dimensions of 100 ∼ 660 μm long, 20 ∼ 200 μm wide, and 2.4 μm thick were also evaluated. The result shows that bending strength and tensile strength of polysilicon microstructures show size effect on the size of the specimens. Statistical analysis of bending strength and tensile strength for various specimen sizes shows that the average bending strength of polysilicon microcantilever beams is (2.885 ± 0.408) GPa, and the average tensile strength of polysilicon thin films is (1.36 ± 0.14) GPa. Statistical analysis of the specimen size effects on the tensile strength predicated the size effects on the length, the surface area and the volume of the specimens due to microstructural and dimensional constrains. The fracture strength increases with the increase of the ratio of surface area to volume. In such cases the size effect can be traced back to the ratio of surface area to volume as the governing parameter. The test data accounts for the uncertainties in mechanical properties and may be used in the future reliability design of polysilicon MEMS structures.

MECHANICAL PROPERTIES AND SCALING EFFECTS IN MICRO-ELECTRO-MECHANICAL SYSTEMS

Piezoelectric Planar Parallel Microrobot with High Bandwidth and Precision for Micromanipulation

Macro modeling method for electrostatic-drive silicon diaphragm

RESEARCH ON SEVERAL MECHANICAL PROBLEMS IN MICROELECTROMECHANICAL SYSTEMS

Structural Model of Electrostatically Actuated Micromechanical Component

RESEARCH OF THE SIZE EFFECT ON STRENGTH OF POLYSILICON MICRO-ELECTRO-MECHANICAL DEVICES

Materials for electronically controllable microactuators

An integrated push-to-pull micromechanical device: Design, fabrication, and in-situ experiment

The application of micro field theory to MEMS actuators

Scale Dependence of Tensile Strength of Micromachined Polysilicon MEMS Structures Due to Microstructural and Dimensional Constraints

Recent Efforts in Modelling Combined Rate, Size and Thermal Effects on Single Crystal Strength

Microelectromechanical System Technology and Its Application

Materials Selection In Mechanical Design For Microsensors And Microactuators

Static and Dynamic Mechanical Behaviors of Electrostatic MEMS Resonator with Surface Processing Error

Monotonic and fatigue testing of spring-bridged freestanding microbeams application for MEMS

Study on the design of anti-sticking structures in MEMS under different forces

RESIDUAL STRESSES IN MICRO-ELECTRO-MECHANICAL SYSTEMS

DETERMINATION OF MECHANICAL BEHAVIOR OF MEMS MATERIALS

Design and Development of Novel Electroplating Spring Frame Mems Structure Specimens for the Microtensile Testing of Thin Film Materials

Mechanical Modeling of Mesa-Diaphragm Structures in Microelectromechanical Systems

Micro Structures and Micro Actuators for Implementing Sub-millimeter Robots