Abstract:Combustion synthesis (CS) is a well-known technique for manufacturing intermetallic compounds and intermetallic-matrix composite materials. This research focuses on fabricating NiAl-matrix composites with varying TiC/TiB2 contents as reinforcement, achieved by the combustion synthesis method. The chemical reactions that yield the final NiAl-TiC-TiB2 compounds were interpreted using thermodynamic calculations. The phase analysis and morphology of the composites were investigated using X-ray diffractometry (XRD) and scanning electron microscopy (SEM) characterization techniques, respectively. The findings demonstrate that the NiAl matrix contains evenly distributed TiC-TiB 2 ceramic-based particles, and no oxidation of reactants occurred during the combustion reaction. With an increase in the TiC-TiB 2 reinforcement phases from 0 to 15 Wt. %, the hardness of the NiAl-TiC-TiB 2 product significantly rose from 496 to 1015 Vickers, while the porosity increased from 24% to 39%, attributed to the reduced quantity of melted NiAl available to fill the pores. Examining tribological behavior in synthesized composites involved combining experimental-numerical methods, utilizing sliding wear tests and artificial neural network (ANN) modeling. The wear results revealed decreasing wear rates with reduced loads (from 35 N to 25, and 15 N) and higher TiC/TiB 2 ceramic content. Iron traces at C0 and C10 worn samples were 2.47 and 26.18 Wt. % respectively, which indicates enhanced hardness. The experimental data were used to train and test an artificial neural network (ANN) and statistical analysis revealed a remarkable accuracy of 91% for the ANN model in predicting friction coefficients within SHS-processed composites, as indicated by the R2 value of 0.91 and a MAPE of 6.47.

INFLUENCE OF Ni CONTENT ON TiC-Ni CERMETS BY SHS/PHIP

MECHANICAL PROPERTIES OF TiC-Ni PRODUCED BY SHS AT ROOM AND HIGH TEMPERATURES

TiC-Fe cermets fabricated by SHS

Investigation on microstructure of TiC-Fe cermets prepared by SHS/PHIP

Research on TiC-Ni cermets by SHS and pseudo heat isostatic pressing

Investigation of TiC formation during ball-milling of elemental titanium and carbon

The Effect of Ni Content on the Phase Structures and Electrochemical Properties of V2.1TiNix (x=0.1–0.9) Hydrogen Storage Alloys

Influence of Carbon Contents on the Structure and Tribocorrosion Properties of Tisicn Coatings on Ti6al4v

Effect of Ni content on the microstructure and properties of WCoB-TiC cermets

Effect of Nano-Si3n4 Addition on the Microstructure and Mechanical Properties of Ticn-Based Cermets

Research on TiC-Ni-Mo Composites by Combustion Synthesis

DENSE TiC-Al2O3-Fe CERMET FABRICATED BY SHS

Effect of Copper Content on the Microstructures and Properties of Tib2 Based Cermets by Shs

Fabrication and wear behavior of TiC/TiB 2 -reinforced NiAl intermetallic matrix composites

Effect of (nbti)c Particles on the Microstructure and Hardness of High Chromium and Nickel Indefinite Chilled Cast Iron

Effects of CrMnFeCoNi additions on microstructure, mechanical properties and wear resistance of Ti(C,N)-based cermets

Effect of C content on the surface gradient structure of (Ti, Mo)(C, N) and Ti(C, N)-based cermets

Effect of Cr2C3 addition on microstructure and mechanical properties of Ti(CN)-based cermets

Effect of the Mass Fraction of NiTi–TiB2 SHS-Particles on the Phase Composition, Structure, and Mechanical Properties of Inconel 625–NiTi–TiB2 Composites Produced by Direct Laser Deposition

Effect of Metallic Content on Mechanical Property of Ni/(10NiO-NiFe2O4) Cermets

Influence of TaC content on microstructure and mechanical performance of Ti(C,N)-based cermets fabricated by mechanical activation and subsequent in situ carbothermal reduction