Abstract:Ti(C0.7,N0.3)-Mo2C–Ni cermets are fabricated by powder metallurgy methods. We systematically investigate the microstructure, fracture morphology, crack propagation mechanism, and interface characteristics of Ti(C, N)-based cermets with different Ni binder contents.The increased dissolution of carbides and carbonitrides leads to a large amount of (Mo,Ti)(C,N) solid solution precipitates, which then spontaneously nucleate, resulting in a significant increase in the content of white core-gray rim grains in the cermets with a high binder content. The increased Ni binder largely improves the flexural strength and fracture toughness of the Ti(C,N)-based cermets because of the ductile dispersion toughening. The rim-core interfaces have a superior atomic coherent relationship in all Ti(C,N)-based cermets owing to the small lattice mismatch. The lattice mismatch of the interface between the rim phase and metal binder is remarkably decreased with the increase in the binder content to construct an atomic coherent relationship. Thus, the increased Ni binder promotes atomic ordering at the interface between the ceramic grains and binder and strengthens the grain boundary. The characteristic (111) peak of nickel shifts to a larger angle due to the reduction in the Ni-based solid solution lattice distortion. Therefore, the effect of solid solution strengthening is diminished with the increase in binder content, which results in a decreased binder strength. In the Ti(C,N)-based cermets with low metal binder contents, the fracture of the grain boundary between the ceramic grains and binder is the predominant failure mechanism. The intergranular crack accompanied by crack branching is the main characteristic of crack propagation. A hybrid fracture mode of intergranular and transgranular cracks is observed in the Ti(C,N)-based cermets with a moderate binder content. As the binder content further increases, the plastic yield deformation and subsequent tearing of the metal binder are the main fracture characteristics because of grain boundary strengthening and decreased strength of the binder.

Effect of Metallic Content on Mechanical Property of Ni/(10NiO-NiFe2O4) Cermets

Effect of Metallic Phase on Relative Density of NiFe_2O_4-10NiO Based Cermet for Aluminum Electrolysis

Effects of CrMnFeCoNi additions on microstructure, mechanical properties and wear resistance of Ti(C,N)-based cermets

Effect of Ni Content on the Microstructure, Mechanical Properties and Erosive Wear of Mo2NiB2–Ni Cermets

Fabrication, microstructure evolution, and mechanical properties of Ti(C,N)-HfN-WC-Ni-Mo cermets

Effect of Mo Content on In-Situ Anisometric Grains Growth and Mechanical Properties of Mo2FeB2-Based Cermets

Microstructure and Properties of Ti(C,N)-Based Cermets with AlxCoCrFeNiTi Binder

Tuning microstructure for superb mechanical properties in a Ti(C,N)-(WMoTaNbTi)C-Ni/Co cermets via change sintering temperature

Cr3C2–20%Ni Cermets Prepared by High Energy Milling and Reactive Sintering, and Their Mechanical Properties

Effect of Yb_2O_3 Doping on Performances of 15(20Ni-Cu)/(nife_2o_4-10nio) Cermets

Effect of Cr2C3 addition on microstructure and mechanical properties of Ti(CN)-based cermets

Sintering Mechanism, Microstructure Evolution and Nanomechanical Properties of Cr-added Mo2FeB2 Based Cermets

Fracture Behaviors of Ti(C, N)-based Cermets with Different Contents of Metal Binder

Highly conductive low nickel content nano-composite dense cermets from nano-powders made via a continuous hydrothermal synthesis route

MECHANICAL PROPERTIES OF TiC-Ni PRODUCED BY SHS AT ROOM AND HIGH TEMPERATURES

Effect of metallic content on sintering behavior of NiFe2O4-based cermet inert anode for aluminum electrolysis

Effect of Molybdenum Addition on the Microstructure and Mechanical Properties of Cr3c2-20 Wt. % Ni Cermet

Effect of Cr<sub>2</sub>C<sub>3</sub> Addition on Microstructure and Mechanical Properties of Ti(CN)-Based Cermets

Effect of Y2O3 Addition on the Microstructure and Mechanical Properties of TiCN-based Cermets

Effect of Nano-Si3n4 Addition on the Microstructure and Mechanical Properties of Ticn-Based Cermets

Effects Of Mechanical Ball Milling Time On The Microstructure And Mechanical Properties Of Mo2nib2-Ni Cermets