Abstract:Under the background of achieving carbon dioxide peaking and carbon neutrality, the rapid development of renewable energy power generation poses new challenges to the flexible adjustment capabilities of traditional power plants. To explore the furnace combustion stability and optimal operation modes during deep peak shaving, a simulation of the combustion process under low-load conditions for a 600 MW wall-fired boiler is performed utilizing computational fluid dynamics (CFD) analysis. The impact of burner combination modes on the combustion process within the furnace is explored at 25% and 35% boiler maximum continuous ratings (BMCRs). This study investigates two configurations of burner combinations. One mode operates burners in layers A, B, and C, which include the lower layers of burners on the front and rear walls of the boiler, as well as the middle-layer burners on the rear wall, referred to as OM1. The other mode operates burners in layers A and C, which include the lower layers of burners on the front and rear walls of the boiler, referred to as OM2. The results indicate that OM2 exhibits superior capabilities in orchestrating the distribution of the airflow velocity field and temperature field under the premise of ensuring no more than a 1% decrease in the pulverized coal burnout rate. When OM1 is employed, the airflow ejected from the middle-level burners hinders the upward movement of pulverized coal sprayed from the lower-level burners, causing a larger proportion of pulverized coal to enter the ash hopper for combustion. Consequently, the ash hopper attains a peak mole fraction of CO2 at 0.163. OM2 delays the blending of pulverized coal with air by enhancing the injection quantity of pulverized coal per burner. As a result, the generation of CO in the ash hopper reaches a notable mole fraction of up to 0.108. The decreased furnace temperature promotes the formation of fuel-based NOx during low-load operation. Taking the 25% BMCR as an example, the NOx emissions measured at the furnace outlet are 743 and 1083 ppm for OM1 and OM2, respectively. This study focuses on the impact of combustion combinations on the combustion stability when the boiler is operating at low loads. The findings could enrich previous research on combustion stability and contribute to the optimization of combustion schemes for power plant boilers operating at low loads.

Safety analysis of operation of water walls of a 300 MW once-through boiler in peak load operation

Investigation on Hydrodynamic Performance and Wall Temperature of Water-Cooled Wall in 1000 MW Boiler Under Low-Load Conditions

Thermal–Hydraulic Calculation and Analysis on Water Wall System of a 700 MWe Ultra-Supercritical CFB Boiler

Steam Temperature Characteristics in Boiler Water Wall Tubes Based on Furnace CFD and Hydrodynamic Coupling Model

Safety Analysis on the Heating Surfaces in the 660 MW Ultra-Supercritical CFB Boiler under Sudden Electricity Failure

The hydrodynamic characteristics of embattlement shaped water wall of a 350 mw supercritical circulating fluidized bed boiler

Safety Analysis on the Water Wall in the 350 MW Supercritical CFB Boiler under Sudden Electricity Failure

The integrated analysis of economy and safety on SOFA running mode of a 600MWe boiler

Computational Analysis of Tube Wall Temperature of Superheater in 1000 MW Ultra-Supercritical Boiler Based on the Inlet Thermal Deviation

A Real-Time Calculation Method to Improve Boiler Safety in Deep Peak Shaving Cases

Leakage of water-cooled wall tube in subcritical boiler

Numerical Study of Supercritical Opposed Wall-Fired Boiler Furnace Temperature and High-Temperature Heating Surface Stress under Variable Load Operation

Analysis and Referential Significance of a Breakdown Accident of the Main Feed Water Pump in a 350 MW Supercritical CFB Boiler

Numerical Study on Combustion Characteristics of a 600 MW Boiler Under Low-Load Conditions

Analysis and Solution of High-temperature Corrosion for a 1000 MW Ultra-supercritical Boiler

Simulation of low-load operation for a 350 MW supercritical unit

Safety Testing and Analysis of the Header of the Drawn Boiler with a Small Diameter and a Large Wall Thickness

Numerical Simulation Study on the Stable Combustion of a 660 MW Supercritical Unit Boiler at Ultra-Low Load

Development of the Design of a 600 MW Low Mass Flow Speed Supercritical Pulverized Coal-fired Boiler with a Vertical Tube Coil

Analysis of the Causes of the Emergency Shutdown of Natural Gas-Fired Water Peak Boilers at the Large Municipal Combined Heat and Power Plant

Experimental investigation on dynamic characteristics of water wall during transcritical process of deep peak regulation for supercritical CFB boilers