Abstract:The solid/gas eutectic unidirectional solidification process is a new kind of technology fabricating the lotus-type porous structure. Besides having the properties of large specific surface area, excellent sound absorption, penetrating performance etc. of traditional porous materials, the particularity of the lotus-type porous structure makes it has extraordinary mechanical and thermal properties. There is a great potential for lotus-type porous aluminum in the field of lightweight engineering and heat dissipation of chip owing to its low density, outstanding corrosion resistance and high thermal conductivity. However, the fabrication of lotus-type porous aluminum has always been been more difficulty than other metals. Until porous aluminum with excellent pore structure was fabricated under very small solidification rates (0.008 similar to 0.015 mm/s) and high superheat degrees of melt (240 similar to 340 K), the proper processing parameters were recognized to be essential for the coupled growth of solid/gas phases for Al-H-2 system, especially the solidification rate. In this work, a three-dimensional time-dependent model describing the evolution of single pore was established based on the theoretical analysis of mass transfer, gas bubble nucleation, pore growth, interruption and detachment. The morphology of single pore under different solidification rates were simulated during the Gasar process by using the finite difference method for Al-H-2 system. The research reveals: coupled growth of solid/gas phases can be achieved under the solidification rates from 0.15 mm/s to 0.005 mm/s. The average pore diameter which ranges from 100 pm to 1100 pm increases with decreasing the solidification rate. The pore length also increases while the pore aspect ratio is nearly a constant about 40 with decreasing the solidification rate. The simulated average pore diameter is in good agreement with the experimental values when solidification rate equals to 0.015 mm/s, and then being slightly lower than the experimental ones with decreasing the solidification rate. The diffusion of hydrogen into the melt during the solidification process is regarded as the main reason of the discrepancy between simulated and experimental average pore diameters. The maximum value of the simulated solidification rates for coupled growth of solid/gas phases in Al-H-2 system first increases from less than 0.01 mm/s to 0.15 mm/s and then being a constant, while the minimum ones increase from about 0.0001 mm/s to 0.01 mm/s with improving the overheat degree of melt and hydrogen partial pressure. By comparing the relative parameters of Al-H-2 and Cu-H-2 systems, the solubility of hydrogen is regarded to be the main parameter which determines solidification rates of coupled growth of solid/gas phases for Al-H-2 system.

Determination of threshold pressure for infiltration of liquid aluminium into short alumina fiber preform

An Analytical Model for Pressure Distribution in Automated Fiber Placement on Irregular Surfaces and Its Application in Aeronautical Manufacturing

Numerical Simulation of Infiltration Behavior of ZTAP/HCCI Composites

Study on Numerical Simulation of Mold Filling and Solidification Processes under Pressure Conditions

Pressure infiltration of molten aluminum for densification of environmental barrier coatings

Study of fabricating technology of a porous aluminum alloy

Prediction method of shrinkage cavity and shrinkage porosity in solidification process under low-pressure casting

Statistical Investigations of Serpentine Channel Pouring Process Parameters on Semi-Solid ZL101 Aluminum Alloy Slurry Using Response Surface Methodology

Simulation and Experimental of Infiltration and Solidification Process for Al2O3(3D)/5083Al Interpenetrating Phase Composite for High Speed Train Prepared by Low-Pressure Infiltration

Dislocation Density-Based Model for Flow Behavior of a Near-α Titanium Alloy Considering Effects of Initial Lamellar Thickness

Investigation of the generation mechanism of the internal pressure of metal thin-walled tubes based on liquid impact forming

Simulation Analysis on Micro Hole Forming of Aluminum Alloy in Extrusion Casting Process

Numerical Simulation of Aluminum Foams by Space Holder Infiltration

Determination Of The Metal/Die Interfacial Heat Transfer Coefficient And Its Application In Evaluating The Pressure Distribution Inside The Casting During The High Pressure Die Casting Process

Analytical prediction of keyhole porosity in laser powder bed fusion

Interfacial research on interpenetrating network structure ZrO2/Al-Mg composites prepared by Extrusion Freeform Fabrication 3DP and pressureless infiltration

Characteristics of Mold Filling and Entrainment of Oxide Film in Low Pressure Casting of A356 Alloy

Microstructure simulation in pressurized solidification during squeeze casting of aluminum alloy A356

Uncovering the effects of local pressure and cooling rates on porosity formation in AA2060 Al-Li Alloy

3D actual microstructure-based modeling of non-isothermal infiltration behavior and void formation in liquid composite molding

MODELING AND SIMULATION OF STRUCTURAL FORMATION OF POROUS ALUMINUM IN GASAR SOLIDIFICATION