Abstract:SiC fiber-reinforced SiC ceramic matrix composites (SiCf/SiC CMCs) are being increasingly used in the hot sections of gas turbines because of their light weight and mechanical properties at high temperatures. The objective of this investigation was the development of a thermal/environmental barrier coating (T/EBC) composite coating system consisting of an environmental barrier coating (EBC) to protect the ceramic matrix composites from chemical attack and a thermal barrier coating (TBC) that insulates and reduces the ceramic matrix composites substrate temperature for increased lifetime. In this paper, a plasma spray-physical vapor deposition (PS-PVD) method was used to prepare multilayer Si–HfO2/Yb2Si2O7/Yb2SiO5/Gd2Zr2O7 composite coatings on the surface of SiCf/SiC ceramic matrix composites. The purpose of this study is to develop a coating with resistance to high temperatures and chemical attack. Different process parameters are adopted, and their influence on the microstructure characteristics of the coating is discussed. The water quenching thermal cycle of the coating at high temperatures was tested. The results show that the structure of the thermal/environmental barrier composite coating changes after water quenching because point defects and dislocations appear in the Gd2Zr2O7 and Yb2SiO5 coatings. A phase transition was found to occur in the Yb2SiO5 and Yb2Si2O7 coatings. The failure mechanism of the T/EBC composite coating is mainly spalling when the top layer penetrates cracks and cracking occurs in the interface of the Si–HfO2/Yb2Si2O7 coating.

Pressure infiltration of molten aluminum for densification of environmental barrier coatings

Improved water vapor resistance of environmental barrier coatings densified by aluminum infiltration

Infiltration thermodynamics in wrinkle-pores of thermal sprayed coatings

Corrosion behavior and failure mechanism of amorphous Al2O3 coating at high-temperature LBE

Low temperature in-situ formation of oxygen barriers by heat treatment of aluminum infiltrated environmental barrier coatings

Influence of pores on the surface microcompression mechanical response of thermal barrier coatings fabricated by atmospheric plasma spray - Finite element simulation

Thermo-Mechanical Behavior Analysis of Pressure Infiltration Casting Process for Manufacturing Open-Cell Metal Foam

Investigation on the Kinetics of Infiltration of Liquid Aluminium into an Alumina Fibrous Preform

The Corrosion Behavior of Al/Al2O3 Composite Films with Ultra-Dense Structure Exposed to Lead-Bismuth Eutectic at 450 to 650 °C

Pore Filling Behavior of Air Plasma Spray Thermal Barrier Coatings under CMAS Attack

Determination of threshold pressure for infiltration of liquid aluminium into short alumina fiber preform

Effect of Internal Oxidation on the Interfacial Morphology and Residual Stress in Air Plasma Sprayed Thermal Barrier Coatings

Simulation and Experimental of Infiltration and Solidification Process for Al2O3(3D)/5083Al Interpenetrating Phase Composite for High Speed Train Prepared by Low-Pressure Infiltration

Microstructure and Hardness Performance of a SiCp/Al Composite by Pressureless Infiltration Technique

Rear Earth Oxide Multilayer Deposited by Plasma Spray-Physical Vapor Deposition for Envisaged Application as Thermal/Environmental Barrier Coating

Flow of Molten Aluminum in Porous Medium during Centrifugal Infiltration Casting Process

Mechanical-Chemical Coupling Effects on an Environmental Barrier Coating System under High-Temperature Water Vapour Conditions

Preparation of Al 2 O 3 –zro 2 –Y 2 O 3 Composite Coatings by a Modified Sol–Gel Technique for Thermal Barrier Application

Effect of Pore Evolution on Thermal Diffusivity and Radiation Characteristics of Thermal Barrier Coatings after High-Temperature Exposures

Influence of Pores on the Thermal Insulation Behavior of Thermal Barrier Coatings Prepared by Atmospheric Plasma Spray

Study on Numerical Simulation of Mold Filling and Solidification Processes under Pressure Conditions