Abstract:Ternary in situ composites based on poly(butylene terephthalate) (PBT), polyamide 66 (PA66), and semixflexible liquid crystalline polymer (LCP) were systematically investigated. The LCP used was an ABA30/PET liquid crystalline copolyesteramide based on 30 mol % of p-aminobenzoic acid (ABA) and 70 mol % of poly(ethylene terephthalate) (PET). The specimens for thermal and rheological measurements were prepared by batch mixing, while samples for mechanical tests were prepared by injection molding. The results showed that the melting temperatures of the PET and PA66 phases tend to decrease with increasing LCP addition. They also shifted toward each other due to the compatibilization of the LCP. The torque measurements showed that the ternary blends exhibited an apparent maximum near 2.5-5 wt % LCP. Thereafter, the viscosity of the blends decreased dramatically at higher LCP concentrations. Furthermore, the torque curves versus the PA66 composition showed that the binary PBT/PA66 blends can be classified as negative deviation blends (NDBs). The PBT/ PA66/LCP blends containing up to 15 wt % LCP were termed as positive deviation blends (PDBs), while the blends with the LCP greater than or equal to 25 wt % exhibited an NDB behavior. Finally, the tensile tests showed that the stiffness and tensile strength of ternary in situ composites were generally improved with increasing LCP content. The impact strength of ternary composites initially increased by the LCP addition, then deteriorated when the LCP content was higher than 10 wt %. The correlation between the mechanical properties and morphology of the blends is discussed. (C) 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1975-1988, 2000.

In-situ composite; the blends of PET with a thermotropic liquid crystalline polyester

Rheological Properties of PET/PA66/Liquid Crystalline Copolyesteramide Blends

Liquid Crystalline Pet/60hba-Mwnts Composite: Synthesis, Characterization, and Properties

In Situ Composites Based On Blends Of Peek And Thermotropic Liquid Crystalline Polymer

The Structure and Physical Properties of in Situ Composites Based on Semiflexible Thermotropic Liquid Crystalline Copolyesteramide and Poly(Butylene Terephthalate)

Study on the injection-molding blends of PET and LCP

PET in Situ Composites Improved Both Flame Retardancy and Mechanical Properties by Phosphorus-Containing Thermotropic Liquid Crystalline Copolyester with Aromatic Ether Moiety

Properties of in situ Composites Based on Semiflexible Thermotropic Liquid Crystalline Copolyesteramide and Polyamide 66 Blends

In-situ composite based on poly (ethylene terephthalate), polyamide and polyethylene with microfibers formed through extrusion and hot stretching

Study on in Situ Reinforcing and Toughening of A Semiflexible Thermotropic Copolyesteramide in Pbt/Pa66 Blends

In Situ Fibrillation of PET/Pglass Composites Reinforced Polypropylene

Morphology-Tensile Behavior Relationship in Injection Molded Poly(Ethylene Terephthalate)/Polyethylene and Polycarbonate/Polyethylene Blends (I) - Part I - Skin-Core Structure

Preparation and properties of injection-moulded blends of poly(vinyl chloride) and liquid crystal copolyester

In-situ Composite Based on Poly （ethylene Terephthalate）,polyamide and Polyethylene with Microfibres Formed Through Extrusion and Hot Stretching

In Situ Reactive Interfacial Compatibilization of Poly(Ethylene Terephthalate)/Metallocene Polyethylene Blends

Morphology and Properties of Injection-Moulded Recycled Poly(Ethylene Terephthalate)/Poly(Ethylene Octene) Blends

Compatibility and Toughening Mechanism of Poly(ethylene Terephthalate)/polycarbonate Blends

Structure and Property Studies of Liquid Crystalline Poly(Ester Imide)/Pet Blends

STUDY ON TLCP/GF/PPESK COMPOSITES

Poly(ethylene Terephthalate)/polyethylene Composite Based on In-Situ Microfiber Formation

Balanced Strength and Ductility Improvement of in Situ Crosslinked Polylactide/Poly(Ethylene Terephthalate Glycol) Blends