Abstract:To explore the W nanoparticles effects on the subsurface microstructural self-organization of Cu-Ag two-phase alloys and the resulting wear performance, we have fabricated bulk nanostructured Cu-10 at% Ag-10 at% W ternary alloys by high energy ball milling and warm pressing. During ball milling, Ag is dissolved into the Cu matrix but W remains immiscible. Compaction of the powders into bulk at 300 °C leads to the Ag precipitation. The as-pressed Cu-10 at% Ag-10 at% W ternary alloy has Ag-rich precipitates size (dAg) of 22 nm and W particles size (dw) of 26 nm. Further annealing at 600 °C for 1 h only increases dAg and dw to 52 nm and 41 nm, respectively. The fabricated Cu-10 at% Ag-10 at% W ternary alloys thus demonstrate enhanced coarsening resistance. The two alloys were then subjected to dry sliding wear against stainless steel disks. It is found that the initial length scale of Ag-rich precipitates and W particles has a profound influence on the microstructure evolution during wear and accordingly on the wear performance. For the as-pressed sample with small dAg and dW, severe plastic deformation (SPD) by wear forced the formation of Cu-Ag homogeneous solid solution, leading to low wear resistance. In contrast, for the annealed one with relatively large dAg and dW, the Cu, Ag and W three phases co-existed but the Ag-rich precipitates were transformed into wavy nanolayers, providing enhanced wear resistance. Compared with Cu-Ag alloys subjected to sliding wear, the presence of W nanoparticles was found to hinder the formation of self-organized nanolayered structure and leads to a small deformation depth. The obtained results provide deep insights into the plastic deformation mechanisms in ternary alloys and the design of wear resistant engineering materials.

Dry sliding tribological properties and subsurface structure of nanostructured copper at liquid nitrogen temperature

Sliding Wear Behavior of Fully Nanotwinned Cu Alloys

A low-to-high friction transition in gradient nano-grained Cu and Cu-Ag alloys

Dry sliding wear of Cu–15Ni–8Sn alloy

Microstructural evolution of pure copper subjected to friction sliding deformation at room temperature

Atomistic scale tribological behaviors in nano-grained and single crystal copper systems

Tribological Properties of Nanocrystalline Cu Coatings Produced by Electroless Plating under Various Lubrication Conditions

Self-lubricating behavior of a PdCuNiP glassy alloy by in-situ nanocrystallization during dry friction

Experiments and molecular dynamic simulations on the cryogenic tribological behaviors of pure silver in liquid nitrogen

Nano-tribological behavior of CuCoCrFeNi high-entropy alloys at cryogenic temperature: A molecular dynamics study

Torsional Fretting and Torsional Sliding Wear Behaviors of CuNiAl Against 42crmo4 under Dry Condition

Molecular dynamics simulation of dry sliding between non-Gaussian copper rough surfaces

Microstructural changes and dry sliding wear behavior of Cu-15Ni-8Sn-0.5Co alloy during deformation and aging treatment

High-Speed Dry Tribological Behaviors of Crnimo Steel in Nitrogen and Oxygen Atmospheres

Mechanisms of near-surface structural evolution in nanocrystalline materials during sliding contact

Dry Sliding Wear Behavior of Mg-Zn-Gd Alloy before and after Cryogenic Treatment

Effects of nanocrystalline microstructure on the dry sliding wear behavior of a Cu-10 at% Ag-10 at% W ternary alloy against stainless steel

Dry sliding wear behavior of in situ Cu–TiB2 nanocomposites against medium carbon steel

Nanoscale self-organization reaction in Cu-Ag alloys subjected to dry sliding and its impact on wear resistance

Dry Sliding Friction and Wear Behavior of Cu-Nanosized TiB2 In-situ Composites

Effect of cryo-rolling on mechanical properties and microstructure of pure copper